Premium Essay

Unit 10 Lab 1

In:

Submitted By Cliff6
Words 592
Pages 3
Once a fiber optic cable plant, network, system or link is installed, it needs to be tested for four reasons: to insure the fiber optic cable plant was properly installed to specified industry standards. to insure the equipment intended for use on the cable plant will operate properly on the cabling to insure the communications equipment is working to specifications to document the cable plant and network for reference in case of future problems Tools and Test Equipment Needed The following tools are needed to test and troubleshoot the fiber optic cable plant, system or link properly. Optical Loss Test Set or power meter and test source with optical ratings matching the specifications of the installed system and proper connector adapters. An OLTS that merely tests cable plant loss may not include a calibrated power meter needed for testing transmitter and receiver power, so a calibrated power meter and source are a better choice for link or system testing. Reference test cables with proper sized fiber and connectors and compatible mating adapters of known good quality. These do not generally need to be “reference quality” but only in good condition, generally defined as having connector losses of less than 0.5 dB. Visual fiber tracer and/or visual fault locator Connector inspection microscope with magnification of 100-200X and fixturing for proper connectors. Video microscopes are recommended. e. Cleaning supplies intended specifically for the cleaning of fiber optic connectors, The Optional: OTDR with long launch and receive cables 3. Testing And Troubleshooting the Installed Cable Plant All fiber cable plants require certain basic tests to insure they were installed correctly and meet expected performance values. These are guidelines for testing and troubleshooting the cable plant itself. The most valuable data one can have for troubleshooting is the installation

Similar Documents

Premium Essay

Nt1310 Unit 10 Lab 1 Essay

...NT1310 Codi Roebuck Unit 10 Lab 1 01/04/2016 Professor: Ronald j. wojcik Fiber optics for diagnostics and troubleshooting are used in varying capacities to test, measure, analyze, transmit, distribute, and/or simulate an optical signal with which the technician can perform procedures and processes associated with maintenance, problem solving, and calibration of equipment and/or networks. Normally in these applications, fiber optic products are used to create loop tests or transmit signals from point-to-point (either single-point to single-point, or single-point to multiple-points). For loop testing, commonly referred to as loopback testing, a signal is sent from a piece of equipment through a loopback or cable and returned to the source, simulating a complete network connection. This type of test allows technicians to perform function tests and internal diagnostic processes without the equipment being physically tied to an active network. This type of setup provides technicians with the advantage of easily isolating individual components for faster, more comprehensive analysis. With signal transmission applications, technicians generally use cables (multiple types for different applications) to connect one or more pieces of...

Words: 678 - Pages: 3

Free Essay

Network

...Network Technology and Service Integration Unit 1 Homework The following homework is designed to cover the course objectives for this unit. Assignment 1.1: Textbook/Workbook Assignments • Complete the following exercises and questions from Routers and Routing Basics: CCNA 3 Labs and Study Guide: Vocabulary Exercise: Matching on page 3 VLSM Subnetting a Subnet Exercises on pages 9-11 VLSM Addressing Design Scenarios 1-6 on pages 15-20 Summary Route Exercises on pages 21-24 Concept Questions on pages 25-27 VLSM Case Study on page 27 Internet Research on page 29 (Use the ITT Tech Virtual Library.) • Complete Chapter 9 Review Questions 2-7, 10, 14, 20-22 on pages 258-259 of Introduction to Telecommunications. Submit your written answers to your instructor at the beginning of Unit 2. . Assignment 1.2: Virtual Labs • Complete Virtual Labs 6, 7, and 8 from the CCNA 640-802 CCNA Simulator, which you can find by clicking through these paths: ICND1 Troubleshooting Scenarios Lab 6: IP Addressing and Routing. ICND1 Troubleshooting Scenarios ICND1 Part 4: Troubleshooting Labs Lab 7: IP Routing I ICND 2 Troubleshooting Scenarios Lab 13: IP Routing II Submit your written answers to your instructor at the beginning of Unit 2. ©ITT Educational Services, Inc: Date: 03/13/09 Network Technology and Service Integration Unit 2 Homework The following homework is designed to cover the course objectives for this unit. Assignment 2.1: Textbook/Workbook Assignments • Complete the following exercises...

Words: 2825 - Pages: 12

Premium Essay

Nt 1210

...ITT Technical Institute NT1210 Introduction to Networking Onsite Course SYLLABUS Credit hours: 4.5 Contact/Instructional hours: 56 (34 Theory Hours, 22 Lab Hours) Prerequisite(s) and/or Corequisite(s): Prerequisites: NT1110 Computer Structure and Logic or equivalent Course Description: This course serves as a foundation for the study of computer networking technologies. Concepts in data communications, such as signaling, coding and decoding, multiplexing, circuit switching and packet switching, OSI and TCP/IP models, LAN/WAN protocols, network devices and their functions, topologies and capabilities are discussed. Industry standards and the development of networking technologies are surveyed in conjunction with a basic awareness of software and hardware components used in typical networking and internetworking environments Introduction to Networking Syllabus Where Does This Course Belong? This course is required for the associate program in Network System Administration and the associate program in Electrical Engineering Technology. The following diagrams demonstrate how this course fits in each program. Associate Program in Network Systems Administration NT2799 NSA Capstone Project NT2580 Introduction to Information Security NT2670 Email and Web Services NT2640 IP Networking PT2520 Database Concepts NT1330 Client-Server Networking II NT1230 Client-Server Networking I NT1430 Linux Networking PT1420 Introduction to Programming NT1110...

Words: 4400 - Pages: 18

Premium Essay

Nt1210 Introduction to Networking Onsite Course

...ITT Technical Institute NT1210 Introduction to Networking Onsite Course SYLLABUS Credit hours: 4.5 Contact/Instructional hours: 56 (34 Theory Hours, 22 Lab Hours) Prerequisite(s) and/or Corequisite(s): Prerequisites: NT1110 Computer Structure and Logic or equivalent Course Description: This course serves as a foundation for the study of computer networking technologies. Concepts in data communications, such as signaling, coding and decoding, multiplexing, circuit switching and packet switching, OSI and TCP/IP models, LAN/WAN protocols, network devices and their functions, topologies and capabilities are discussed. Industry standards and the development of networking technologies are surveyed in conjunction with a basic awareness of software and hardware components used in typical networking and internetworking environments Introduction to Networking Syllabus Where Does This Course Belong? This course is required for the associate program in Network System Administration and the associate program in Electrical Engineering Technology. The following diagrams demonstrate how this course fits in each program. Associate Program in Network Systems Administration NT2799 NSA Capstone Project NT2580 Introduction to Information Security NT2670 Email and Web Services NT2640 IP Networking PT2520 Database Concepts NT1330 Client-Server Networking II NT1230 Client-Server Networking I NT1430 Linux Networking PT1420 Introduction to Programming NT1110...

Words: 4400 - Pages: 18

Premium Essay

Nt2640

.../Instructional hours: 34 Theory, 22 Lab Prerequisite: NT1210 Introduction to Networking or equivalent Course Revision Table Change Date Updated Section Change Description Change Rationale Implementation Quarter 07/18/2011 All New Curriculum New Curriculum September 2011 02/19/2013 All Updated labs across the course to map the 2nd edition of lab manual Immediately 02/27/2013 Midterm and Final Examination Answer Keys Added examination keys Immediately 03/18/2013 Answer Keys for Midterm and Final Updated some answers to address the accuracy March 2013 04/19/2013 Assignment labels on Pages 43, 52, 61, 78, 87, 97, 106 and 132. Added labels to identify additional assignments in affected units Clarification of additional assignments March 2013 Table of Contents COURSE OVERVIEW 5 Catalog Description 5 Goals and Expectations 5 Learning Objectives and Outcomes 6 Career Impact 6 INSTRUCTIONAL RESOURCES 7 Required Resources 7 Additional Resources 7 COURSE MANAGEMENT 9 Technical Requirements 9 Test Administration and Processing 9 Replacement of Learning Assignments 10 Communication and Student Support 10 Academic Integrity 10 GRADING 11 COURSE DELIVERY 13 Instructional Approach 13 Methodology 13 Facilitation Strategies 14 UNIT PLANS 15 Unit 1: The TCP/IP Model, LANs, WANs, and IP Networks 15 Unit 2: TCP/IP Network, Transport, and Application Layers 24 Unit 3: IP Subnetting and Basic Router Configuration 34 Unit 4: IP Routing with Connected, Static...

Words: 22068 - Pages: 89

Premium Essay

Unit 1 Labs

...ITT TECHNICAL INSTITUTE NT1210 Introduction to Networking Onsite Course GRADED ASSIGNMENTS Graded Assignment Requirements Retain all handouts issued in every unit, as well as any assignment, research, or lab documents you prepare as part of assignments and labs. Some may be used more than once in different units. NOTE: Always check with your instructor for specific due dates of assignments. Graded Assignments Unit 1 Assignment 1: Computer Basics Review Course Objectives and Learning Outcomes Identify the major needs and major stakeholders for computer networks and network applications. Describe how digital devices store data. Describe the differences between input and output devices. Assignment Requirements In the Chapter Review Activities at the end of Chapter 1 in the Odom textbook (answers can be found in the textbook): Respond to the multiple-choice questions. Complete the List the Words inside Acronyms table. Required Resources Odom textbook Computer with word processing software Internet access Printer Submission Requirements: Submit your responses as a typed document using Arial or Times New Roman 12-point font, double-spaced. Label your assignment Unit 1 Assignment 1. Unit 2 Assignment 1: Identifying Network Topologies Course Objectives and Learning Outcomes * Identify the major needs and major stakeholders for computer networks and network applications. * Identify the classifications of networks and how they are...

Words: 16182 - Pages: 65

Premium Essay

Police Abuse Essay

...ITT TECHNICAL INSTITUTE NT1210 Introduction to Networking Onsite Course GRADED ASSIGNMENTS Graded Assignment Requirements Retain all handouts issued in every unit, as well as any assignment, research, or lab documents you prepare as part of assignments and labs. Some may be used more than once in different units. NOTE: Always check with your instructor for specific due dates of assignments. Graded Assignments Unit 1 Assignment 1: Computer Basics Review Course Objectives and Learning Outcomes * Identify the major needs and major stakeholders for computer networks and network applications. * Describe how digital devices store data. * Describe the differences between input and output devices. Assignment Requirements In the Chapter Review Activities at the end of Chapter 1 in the Odom textbook (answers can be found in the textbook): * Respond to the multiple-choice questions. * Complete the List the Words inside Acronyms table. Required Resources * Odom textbook * Computer with word processing software * Internet access * Printer Submission Requirements: Submit your responses as a typed document using Arial or Times New Roman 12-point font, double-spaced. Label your assignment Unit 1 Assignment 1. Unit 2 Assignment 1: Identifying Network Topologies Course Objectives and Learning Outcomes * Identify the major needs and major stakeholders for computer networks and network applications. * Identify the...

Words: 16043 - Pages: 65

Premium Essay

Introduction to Networking

...ITT TECHNICAL INSTITUTE NT1210 Introduction to Networking Onsite Course GRADED ASSIGNMENTS Graded Assignment Requirements Retain all handouts issued in every unit, as well as any assignment, research, or lab documents you prepare as part of assignments and labs. Some may be used more than once in different units. NOTE: Always check with your instructor for specific due dates of assignments. Graded Assignments Unit 1 Assignment 1: Computer Basics Review Course Objectives and Learning Outcomes * Identify the major needs and major stakeholders for computer networks and network applications. * Describe how digital devices store data. * Describe the differences between input and output devices. Assignment Requirements In the Chapter Review Activities at the end of Chapter 1 in the Odom textbook (answers can be found in the textbook): * Respond to the multiple-choice questions. * Complete the List the Words inside Acronyms table. Required Resources * Odom textbook * Computer with word processing software * Internet access * Printer Submission Requirements: Submit your responses as a typed document using Arial or Times New Roman 12-point font, double-spaced. Label your assignment Unit 1 Assignment 1. Unit 2 Assignment 1: Identifying Network Topologies Course Objectives and Learning Outcomes * Identify the major needs and major stakeholders for computer networks and network applications. * Identify the...

Words: 16043 - Pages: 65

Premium Essay

Nt1230 Syllabus

...5 Contact/Instructional hours: 56 (34 Theory Hours, 22 Lab Hours) Prerequisite(s) and/or Corequisite(s): Prerequisite or Corerequisite: NT1210 Introduction to Networking or equivalent Course Description: This course introduces operating principles for the client-server based networking systems. Students will examine processes and procedures involving the installation, configuration, maintanence, troublshooting and routine adminstrative tasks of popular desktop operating system(s) for standalone and network client computers, and related aspects of typical network server functions. Client-Server Networking I Syllabus Where Does This Course Belong? 1st QTR GS1140 NT1110 GS1145 Problem Solving Theory Computer Structure and Logic Strategies for the Technical Professional 2nd QTR NT1210 Introduction to Networking NT1230 Client-Server Networking I MA1210 College Mathematics I 3rd QTR NT1310 NT1330 MA1310 4th QTR PT1420 NT1430 EN1320 5th QTR PT2520 NT2580 EN1420 6th QTR NT2640 NT2670 CO2520 7th QTR NT2799 SP2750 Physical Networking Client-Server Networking II College Mathematics II Introduction to Programming Linux Networking Composition I Database Concepts Introduction to Information Security Composition II IP Networking Email and Web Services Communications Network Systems Administration Capstone Project Group Theory The follow diagram indicates how this course relates to other courses in the NSA program: 1 Date: 8/31/2012 Client-Server Networking I Syllabus ...

Words: 1834 - Pages: 8

Premium Essay

Random

...every society faces ... For a given set of laboratory services, there is a defined cost. Nt2580 Lab 4 - Term Papers - Jrains www.termpaperwarehouse.com › Computers and Technology Jan 18, 2013 – Nt2580 Lab 4. 1. Define why change control management is relevant to security operations in an organization. Change control is a systematic ... NT2580 Introduction to Network Security stankong.bol.ucla.edu/NT2580/index.htm Welcome to NT2580 Introduction to Network Security ... Home Work , Labs, PowerPoint , Project and Exam Reviews. Fall Quarter 2012 ... Itt tech nt2580 lab 6 - 6 ebooks - free download www.getbookee.org/itt-tech-nt2580-lab-6/ Itt tech nt2580 lab 6 download on GetBookee.org free books and manuals search - 094 ALB 01-09-13 01-09-13 Vol 37-a. Nt2580 unit 9 lab - 4 ebooks - free download www.getbookee.org/nt2580-unit-9-lab/ Nt2580 unit 9 lab download on GetBookee.org free books and manuals search - NT2580 Introduction to If ti S itInformation Security. Nt2580 unit 6 lab - 4 ebooks - free download www.getbookee.org/nt2580-unit-6-lab/ Nt2580 unit 6 lab download on GetBookee.org free books and manuals search - NT2580 Introduction to If ti S itInformation Security. Lab itt edition nt2580 answers - 1 ebooks - free download www.getbookee.org/lab-itt-edition-nt2580-answers/ Jan 30, 2013 – Lab itt edition nt2580 answers download on GetBookee.org free...

Words: 435 - Pages: 2

Free Essay

Fluid Power

...HYDRAULICS LAB #1 The objective of this lab is to test the fluid flow provided by the power unit at various discharge pressures, and create a power unit characteristic curve. 1. Build on the trainer the hydraulic circuit shown in the figure below, using the components listed here. hydraulic power unit (2) pressure gauges flow control valve (FCV) – simulated load flow-meter Page 1 of 2 2. Initial setup: a. Fully close (CW) the FCV, and fully open (CCW) the pressure relief valve on the power unit. b. Start the power unit, and slowly adjust the pressure relief valve until pressure gauge P1 reaches 50 bar. Let the unit run for a few minutes then check and adjust P1 if necessary. c. Do not touch the pressure relief valve for the remainder of the lab. d. Fully open the FCV. 3. Test: a. Record the pressures P1, P2 and the flow rate under the “Min.” column in the table below. b. Slowly turn the FCV CW, adding a simulated load to the system. When the pressure at P1 increases to 15 bar, stop and record pressure P2 and the flow rate. c. Repeat for all columns listed in the table. The final column, listed as “Max Pres.” should be run with the FCV fully closed. Note the sound of the power unit during this test. You should detect changes in tone as the load (pressure) is increased. P1 Pressure (bar) P2 (bar) Flow Rate (lpm) Min * 15 20 25 30 35 40 45 46 47 48 49 Max. Pres. * minimum pressure attained, with flow control fully open HYDRAULICS LAB #1 Page 2 of 2 Lab Report: ...

Words: 638 - Pages: 3

Free Essay

Sc4730 Assignments

...Exercises………………………………………………………… page 2 Labs…………………………………………………………………………………….page 16 Project…...............................................................................................................page 21 ------------------------------------------------- Graded Assignments Unit 1 Exercise 1: Statistics and Graphing Course Objectives and Learning Outcomes In this assignment, you will interpret and graph descriptive statistics. Assignment Requirements Work in small groups to complete Problems 1-4 given in the worksheet provided by your instructor (Problems Worksheets). This is also available at the link below. Fill out one activity sheet (found at the end of the document) for each of the 4 questions. Required Resources * Statistics and Graphing (SC2730.U1.HO1) Worksheets also available at: http://esa21.kennesaw.edu/activities/stats/stats.pdf * Problems Worksheets (SC2730.U1.HO2) also available at: http://esa21.kennesaw.edu/activities/stats/problems.pdf Submission Requirements 4 completed activity sheets (1 each for Problems 1-4) Unit 1 Problem Set 1: Scientific Method Applied Problem Sets Course Objectives and Learning Outcomes In this assignment, you will outline the steps of the scientific method. Assignment Requirements Refer to the Applied Problem Sets located on pp. 153-162 of the Wagner lab manual. Use the scientific method to complete the problem sets. Answer Questions 1-6 for Problem Set 1 and questions 1-8 for Problem Set 2....

Words: 5239 - Pages: 21

Free Essay

The Joys of Cheating

...7Student Contract 1. Attendance – Science is a subject where everyday something new is being taught. If a student is absent, a note must be presented to his/her teacher when the student returns to class. This note must have information i.e. phone number, contact person and reason for absence. 2. Lateness – Lateness will be taken very seriously and will affect a student’s grade. Students are expected to come to class on time. If you come to class late you must sign the late log and provide the reason for your lateness (i.e. late pass) GRADING POLICY Every student has the right to see how their grade is calculated. In order to discuss individual grade calculations you can set up an appointment during your teacher’s office hours. Your science teacher will explain the grading policy during this meeting. Your child’s grades will also be available for you to view on line through a program called Pupil Path, www.Pupilpath.com Your child will receive the instructions and passwords for this within the first week of school. • Class participation –Class participation covers every aspect of a student’s behavior in the classroom. This includes the questions you ask, the comments you make, the notes you take, completion of class work, notebook check, presenting your reference tables and your prompt arrival to class. Students are expected to remain on task while in class and are accountable for their conduct. Class participation is 20% of your grade • Homework...

Words: 1313 - Pages: 6

Free Essay

Docx

...English IE2 READING & WRITING 1. Course Statistics : 120 periods (8 credits) Number of instruction weeks : 10 Number of sessions : 30 Number of sessions per week :3 Number of periods per session 2. Pre-requisite Number of periods :4 Students who achieved IE1 course score > 50 or scored from 35-60 on the Placement Test are required to take this course. 3. Learning outcome Students who have successfully completed the course are expected to have English proficiency at high intermediate level or higher. 4. Course books Reading Activator (Intermediate) Reading Activator (Advanced) Writing Activator (Intermediate) Writing Activator (Advanced) 5. Additional material ESP Handouts NorthStar 3 – Reading and Writing (3rd edition) 6. Lab Practice 2 sessions 7. Weekly Guide: Week 1 2 Session 1 ESP Unit 01: Information Technology - Handout 1 HW: NorthStar 3 Unit 1: The World of Advertising (pp 01- 10) Unit 02: Construction - Handout 2 HW: NorthStar 3 Unit 03: Going to Extremes Sports and Obsession (pp 3948) Unit 03: Engineering 3 4 Vocabulary and Reference Introduction & Review - Introduction to Reading Skills - R.A.I: pp 14-15; 18-31 - R.A.A: pp19-27 - Introduction to Writing Skills - Review: Paragraph writing (designed by the instructor) Fact and Negative Fact - R.A.I: pp 34-47 - R.A.A: pp 35-43 Independent writing Handout 1 - Overview of independent writing ...

Words: 938 - Pages: 4

Free Essay

Lab Report

...Lab 1: Introduction Metric System Prefixes (to put in front of basic units): k = kilo = 1000 x c = centi = 1/100 of (which is 10-2 of) m = milli = 1/1000 of (which is 10-3 of) ( = micro = 1/1,000,000 of (which is 10-6 of) n = nano = 1/1,000,000,000 of (which is 10-9 of) (d = deci = 1/10 of ) [pic] (Note: The way to read the numbers above, for example, is: There are 1000 nm in one (m. There are 1000 (m in one mm.. etc.) To convert from one metric unit to a different metric unit (a different prefix): 1. First, decide how many places to move the decimal point (the number of 0’s in the chart above indicates the number of places to move the decimal point). 2. Next you need to decide whether to move the decimal point left or right. To decide this, think about which is the smaller unit. (The smaller the unit is, the more of them you need to get the same amount. e.g. pennies vs. dollars) NOTE: Here is another way to write the conversions, using distance (the meter is the basic unit for distance) as an example: 0.001 km = 1 m = 10 dm = 100 cm = 1000 mm = 1,000,000 (m = 1,000,000,000 nm The “staircase” method: One more way to remember about sliding decimal points when converting between prefixes in the metric system! [pic] Move the decimal point 3 places for every step you move on the “staircase”, and in the same direction traveled on the staircase (left vs. right). Unfortunately, you can see that the “c” prefix...

Words: 1090 - Pages: 5