Free Essay

Connector Installations

In:

Submitted By fabian24
Words 591
Pages 3
NT1310 Unit 6 Exercise 1
Luz Garcia
7/22/14

Connector Installations

Twisted-pair cable:
Step 1:
Measure the cable you want to put ends on and trim it to the proper length using the cable cutter.
Step 2: Use the cable stripper to strip about 1.5" of the jacket from the end of the cable. Then, rotate the stripper around the cable twice. This will cut through the jacket.
Step 3: Remove the stripper from the cable and pull the trimmed jacket from the cable, exposing the inner conductors. If a jacket slitting cord (usually a white thread) is present, separate it from the conductors and trim it back to the edge of the jacket.
Step 4: Untwist all the inner conductor pairs and spread them apart so that you can see each individual conductor.
Step 5: Line up the individual conductors so that the color code matches the color-coding standard you are using.

Step 6: This step includes two points. First, trim the conductors so that the ends are even with each other, making sure that the jacket of the cable will be inside the connector. Second, the total length of exposed connectors after trimming should be no longer than 0.5" to 0.625".
Step 7:
Insert the conductors in the connector, ensuring that all conductors line up properly with the pins as they were in the previous step. If they don't line up, pull them out and line up. Do this carefully, as it's the last step before crimping on the connector.
Step 8: Carefully insert the connector and cable into the crimping tool, which has two dies that will press into the connector, and push the pins in the connector into the conductors inside the connector. Now the installation is done.
After the whole installation, you should check to ensure all conductors are making contact and that all pins have been crimped into their respective conductors. If the connector didn't crimp properly, cut off the connector and redo it.

Coaxial cable:
Step #1
Adjust the wire strippers so the first cut is down to the center copper wire. Adjust the second cut so it cuts through the rubber jacket only but not through the wire braiding just below the rubber jacket. This may take several attempts to get the tool adjusted just right.
Step #2
With the stripper properly adjusted insert the cable into the strippers so the end of the cable is flush with the edge of the stripper. Spin the stripper around the cable until it turns freely. Pull the stripper away from the cable while lightly squeezing the jaws of the stripper onto the cable. You should now have a cable ready to install a connector.
Step#3
Slide the proper coax cable connector onto the cable. This sometimes requires a pair of pliers to grip the connector if the fitting is stubborn is does not want to slide on easily. With the coax cable connector properly fitted to the cable insert it into the crimp tool. When the connector is properly in place squeeze the handle to crimp the connector onto the cable. The first slot of the tool is for RG 59 cable and the second slot is for RG 6 coax cable. With the compression connector properly fitted to the cable insert the fitting into the compression tool copper wire first. When the connector is in place squeeze the handle to compress the connector onto the cable. Use the "F" adapter when crimping coax cable for TV.

Similar Documents

Free Essay

Connector Installations

...Connector Installations * Strip the cable of its protective outside jacket about 3-6 inches from the end. This can be done with the cabling scissors by applying pressure from the scissors to the cable and rotating the scissors around the cable. After you have punctured the cables jacket, you should be able pull the jacket off easily leaving exposed wires. * Expose the wire a little further. Stripping the cable can cut and damage the wires at the area that we cut the cable so we want to expose about 6 more inches of fresh wires. Most twisted pair cables have a small string inside the cable to assist with this. * If your cable has the small string. Cut the string after you have enough exposed cable. * Untwist the wires completely to the jacket. Place the wires into the appropriate color slot on the jack. Make sure to place the wires as tightly as possible in the slots in regards to the jacket. There should be as little exposed and untwisted wire as possible to keep the signal strength as high as possible. Make sure to place the White/Blue in the White/Blue spot and not the solid Blue spot. The White/Color wire is not the same as the solid color. * Terminate each wire. After all the wires are in the correct spot and double checked to make sure as little amount of exposed wires will be left as possible, use the punch down tool with the 110 blade and terminate each wire individually. The 110 blade will fully cover the wire connector on the jack. Push down until...

Words: 360 - Pages: 2

Free Essay

Zsfdzfdzf

...================================================================== Robin Hood – The Legend of Sherwood v1.0 Readme file – October 25th, 2002 ================================================================== Thank you for purchasing Robin Hood – The Legend of Sherwood. The Spellbound Team wishes you a lot of fun with their new game. This readme file contains useful information that could help you to solve problems with the game. ================================================================== CONTENTS Getting Started · System Requirements · DirectXtm and driver information · Installing and starting the game · Uninstallation Problems and Solutions · Performance optimisation on slow systems · Known problems · Technical Support ================================================================== GETTING STARTED ================================================================== System Requirements ------------------------------------------------------------------ OS: Windows 98/ME/2000/XP CPU: 233 MHz Intel Pentium II or similar CPU RAM: 64 MB CD/DVD-ROM speed: 4x Hard drive space: 1GB available Video: 4 MB RAM and DirectXtm-compatible Sound: DirectXtm compatible sound device Input: Keyboard, Mouse Recommended: CPU: 500 MHz Pentium III or similar CPU RAM: 128 MB DirectXtm and driver information ------------------------------------------------------------------ ...

Words: 1079 - Pages: 5

Free Essay

Case Analysis

...| 1 Deep Freeze Standard User Guide 2 | Last modified: April, 2010 © 1999 - 2010 Faronics Corporation. All rights reserved. Faronics, Deep Freeze, Faronics Core Console, Faronics Anti-Executable, Faronics Device Filter, Faronics Power Save, Faronics Insight, Faronics System Profiler, and WINSelect are trademarks and/or registered trademarks of Faronics Corporation. All other company and product names are trademarks of their respective owners. Deep Freeze Standard User Guide | Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About Faronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Words: 1981 - Pages: 8

Free Essay

Apple

...(.EXE, 2.5 Mb) Click here to install the MegaStat® add-in for Excel® Mac®: 2011 (.ZIP, 1.8 Mb) Click here to download the MegaStat® User’s Guide (PDF, 3.5 Mb) System Requirements: Operating system (32 or 64 bit): Windows® XP® / Vista® / 7® / 8® and Mac® OS-X® Excel® 32 bit versions: 2007 / 2010 / 2013 and Excel® Mac®: 2011 You must use the version designed for your operating system. If you want more technical details regarding MegaStat® system requirements and the installation process, see the FAQ document posted at www.mhhe.com/megastat. MegaStat® Start-up Instructions  How to Install the Windows® version: After clicking on the link above, you will be prompted to run or save the file. Click ‘Run’ and the add-in will install to a default add-ins directory. You will also get a pop-up window for User Account Control. Click Yes to proceed. It is recommended that you accept all default settings as the program prompts during the installation. You must exit Excel® before running the installation program. The file you are running is an executable (.exe). Some firewalls may block .exe files for security purposes. If you receive warnings when you try to download/run this file, please follow the instructions of your firewall program to allow this download. NOTE: You may need administrative rights to install this software on your computer. To activate MegaStat:  After running the MegaStat® installer program, you need to get MegaStat® on the Excel Add-Ins ribbon...

Words: 1007 - Pages: 5

Premium Essay

Information Technology

...a user’s Documents, Desktop, and other folders so that they are stored on a network drive rather than the local computer 8. Settings in the Kerberos Policy section of Group Policy allow you to configure the maximum allowable clock skew between a client and a domain controller. 9. Auditing for Policy Change Events will alert you when a change is made to User Rights assignments, IPSec policies, or trust relationships. 10. You can create a consistent service startup configuration for multiple computers by using the System Services node in Group Policy. Matching: 1. This feature of Group Policy software installation will automatically reinstall critical application files if they are accidentally or maliciously deleted- G. Self Healing 2. Group Policy software installations rely on this file type to create an installation package that can be cleanly Assigned and Published and that has self-healing capabilities- I. msi file 3. This default security level in software...

Words: 481 - Pages: 2

Premium Essay

Repair Shop

...Unit 10 Analysis 1: Repair Shop NT1110-T Repair Shop Since a computer repair shop will pretty much automatically due two things before working on your computer, which is back up any pictures, videos and documents to a DVD and format the hard drive and reinstall the operating system, it sounds like a good thing to do. However, there can be some pros and some cons to this. The pros would be that everything is backed up and saved on a DVD, therefore none of the customers information is lost on the computer; this would be less time consuming for the customer. The customer would also benefit from a formatted hard drive and the reinstallation of the operating system. Once done, the customer has a repaired computer. The cons to this, is that the customer could be out of a considerable amount of money. Most repair shops will charge for the backup of all files. So it would be best to this on your own before taking it in. Also, the repair shop will not install all the applications that you were using on your computer. Again, you would have to take the time to do this yourself after all repairs are done. Different users can be affected much differently by the policies of this repair shop. Someone with a brand new computer would not have anything to back up versus someone that has had their computer for several years. A user that mostly browses the internet and does not email will not lose documents, files versus a business professional that creates these things on a daily...

Words: 319 - Pages: 2

Free Essay

Scince

...| 1 Deep Freeze Standard User Guide 2 | Last modified: April, 2010 © 1999 - 2010 Faronics Corporation. All rights reserved. Faronics, Deep Freeze, Faronics Core Console, Faronics Anti-Executable, Faronics Device Filter, Faronics Power Save, Faronics Insight, Faronics System Profiler, and WINSelect are trademarks and/or registered trademarks of Faronics Corporation. All other company and product names are trademarks of their respective owners. Deep Freeze Standard User Guide | Contents 3 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About Faronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Words: 1981 - Pages: 8

Free Essay

Corporate Low

...all those 3 informations you are good to go! 1 - Download bootstrap files (Kernel and ramdisk image). # cd /boot # mkdir centos6 # cd centos6 # wget http://mirror.centos.org/centos/6/os/x86_64/isolinux/vmlinuz # wget http://mirror.centos.org/centos/6/os/x86_64/isolinux/initrd.img Add an entry to the Grub Loader # vi /boot/grub/menu.lst ## Add the following lines to the end of the file and count how many lines starts with tittle: title CentOS 6 VNC Installation         root (hd0,0)               kernel /centos6/vmlinuz vnc vncpassword=houseoflinux headless ip=10.0.0.10 netmask=255.255.255.0 gateway=10.0.0.1 dns=10.0.0.5 ksdevice=eth0 method=http://mirror.centos.org/centos/6/os/x86_64/ lang=en_US keymap=us         initrd /centos6/initrd.img In my case with I had total 3 entries because I am updating a CentOS 5.6 to CentOS 6 and I had a couple update. If we have 3 title entries there, the 3rd one should be our CentOS 6 installation but Grub starts counting the first one as 0, so our Centos 6 installation is actually 2 for grub.   Here is my menu.lst file: # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE:  You...

Words: 600 - Pages: 3

Free Essay

Software Development

...in any group policy-based software installation is obtaining the installer file for the software you are deploying. It is a requirement that this installation file be in Microsoft Software Installer (MSI) format. "Once you have obtained the appropriate MSI file, you must create a distribution point for the software to be deployed from. Your distribution point needs to be a centralized location, preferably on a server, where a shared folder can be created that all users have read access to. Once you have created this shared folder, you need only to copy the MSI file into it." "Now that we have prepared our installation file we are ready to create the group policy object that will push out the installation. To do this, we will be using the Group Policy Management Console (GPMC), which is a free download from Microsoft. Create a new GPO by opening the GPMC, clicking on 'Group Policy Objects' in the left pane, and right-clicking in the center pane and clicking 'Create New Group Policy Object.' Finally, type a name for this GPO and hit the Enter key. The name of your GPO should be something brief but descriptive, such as a 'Virus Protection Installation.' "Having a fresh clean GPO to work with, we can now proceed to assigning the installation packing to it. You will begin this by right-clicking your newly created GPO and clicking 'Edit.' Under the Computer Configuration heading, expand 'Software Settings.' Right-click 'Software Installation,' point to 'New,' and click 'Package’...

Words: 368 - Pages: 2

Free Essay

Marketing

...Solution for Installation Error for HP Devices – Windows Vista We have detected that you were unable to successfully complete the installation for your HP device. All of the files that we attempted to install have been removed. Follow the procedures in this document to install your HP device after receiving an installation error. Note|Please make sure you have turned off and restarted your PC before trying the steps outlined below.| Step 1: Run the Disk Cleanup utility The software installation process uses certain system folders for preparing files for installation. Periodically, these folders need to be cleared. Prior to installing again, run the Disk Cleanup utility, which will help you: · Delete temporary Internet files · Delete downloaded program files · Empty the Recycle Bin · Delete files from the temporary folder · Delete files created by other Windows tools · Remove unused, optional Windows components To use the Disk Cleanup utility: 1. Click Start ( ), click All Programs, click Accessories, click System Tools, and then click Disk Cleanup. 2. After the Disk Cleanup utility analyzes the hard drive, a report with a list of options appears on the computer. Click the appropriate check boxes to remove unwanted files from the computer, and then click OK. 3. Click Yes on the confirmation screen that appears on the computer. Step 2: Reinstall HP Software Note|Before starting the installation process again, please confirm the following:· Unplug the USB...

Words: 1178 - Pages: 5

Free Essay

Introduction About Enrolment Grading System

...degree requirements of Worcester Polytechnic Institute. The views and opinions expressed herein are those of the authors and do not necessarily reflect the positions or opinions of Worcester Polytechnic Institute. This report is the product of an educational program, and is intended to serve as partial documentation for the evaluation of academic achievement. The reader should not construe the report as a working document. Abstract The WPI OfCourse! course management system provides educators with a set of tools to extend their existent course websites. While this toolset offers great functionality, the installation and configuration of the system is complex and difficult. The project team created a two-tiered installation package that is both simplified and easy to use. User testing was conducted and indicated a significant improvement in the installation procedure. In conclusion, the OfCourse! system was improved by the newly created installer. -i- Executive Summary As the web evolves and grows, educational professionals continue to pursue the use of online tools. While a variety of software exists, educators of average computer literacy seek a feature-rich application that is easy to install and use. Educators demand a well-designed user interface and a comprehensive set of features. The OfCourse! course management system is a set of online educational tools that can be integrated into existent websites. While the toolset provided is packed with great ...

Words: 6392 - Pages: 26

Premium Essay

Nt1320 Unit 1

...The problem is a bad VGA port on the computer or monitor. I came up with the problem by gathering information from the customer, identifying symptoms by checking the computer and monitor and determining if anything has changed by asking the customer. Information – Problem started 2 years after customer purchased computer and monitor. Desktop computer powers on, but does not display on external monitor. VGA ports are being used on computer and Monitor. Computer and monitor have DVI ports. Identifying symptoms – Monitor display is blank when computer is powered on. Determining if anything has changed – No changes have occurred since purchase of computer and monitor. Step 2: Establish a theory of probable cause. The probable cause of the problem is wear and tear of the computer or monitor VGA port. Step 3: Test the theory to determine the cause. The VGA cord was tested on another computer and monitor and was good. The computer was connected to good monitor using the VGA cord and the display was blank. The monitor was connected to good computer using the VGA cord and display was good. A good DVI cord was used to test the computer and monitor’s DVI ports and both were good. The problem is a damaged VGA port on the computer due to wear and tear. Step 4: Establish a plan of action to resolve the problem. Install a new VGA card on the computer. Step 5: Implement the solution or escalate if necessary. A new VGA card was installed on the computer and the problem was solved. Installing...

Words: 485 - Pages: 2

Free Essay

Zytaba

...machine, such as installing software or performing updates, the computer needs to be put into a Thawed state. A reboot is required every time the state of the computer is changed. Requirements Deep Freeze requires Windows 95/98/Me/2000/XP/Vista and 10% free hard drive space. The hardware requirements are the same as the recommended hardware requirements for the host operating system. Installing Deep Freeze Standard When installing Deep Freeze, close and disable all background utilities and antivirus software. Complete the following steps to install Deep Freeze Standard: 1. 2. Double-click the DeepFreezeSTDEval.exe file to begin the installation process. The Deep Freeze Standard Installation Dialog appears. Click Install to begin the installation. Follow the steps presented. Read and accept the license agreement. At the end of the installation, the machine reboots. After the reboot Deep Freeze is installed. After the reboot, a Password Initialization screen appears. This screen allows you to enter a password for Deep Freeze. This...

Words: 852 - Pages: 4

Free Essay

It Memory Installation

...IT/280 Computer Hardware Fundamentals “CPU and Memory Installation Paper” Student: __________ Instructor: __________ JSTONE Associates LLC requires many different tasks which are performed by out IT department of technicians. Upgrades are a must for any business that wants to stay relevant in the market. We at JSTONE Associates LLC understand these upgrades not just viable but necessary. As our company grows and prospers so much our systems. In this portion of your handbook we will be covering the installation or upgrading of memory within our company. These step by step instructions must be completed as required by our company policy and procedure guidelines. 1. Acquire unit or unit’s specs from the company database to retain the compatible upgraded RAM for the system or systems being updated. 2. Pull the allotted memory upgrades from our warehouse and proceed to your specified area of operation. 3. Power down the unit(s) and remove all connections from the system. 4. Locate and procure a clean and clear area to process the work order. 5. Pull cover from system and clean the unit of dust and other materials with your kit. 6. Wash and dry hands thoroughly and put on company issued static shield bracelet. 7. Carefully pull each individual RAM stick from the motherboard and place the dated hardware in the shield sleeves from your kit. 8. Clear all connections or components that may obstruct your path to the motherboard. 9. If removal...

Words: 488 - Pages: 2

Free Essay

Critique

...CRITIQUE The following is a critique of the Joomla! User Manual 1.0. The URL of the page is as follows http://help.joomla.org/images/User_manual/user_manual_v1%200%201_10%2021%2006.pdf. This a critique of the installation portion. It also covers some features of the Joomla! Installer that is based on browser and the Manual Installation. The links for these are http://help.joomla.org/content/view/39/165/ and http://help.joomla.org/content/view/40/132/ respectively. Only recently, I installed the software Joomla!. At first I tried the “easy browser install”. But I couldn’t do it and I failed. I then tried using the manual for instructions to help me to install the software. But, the installation procedure through the user manual took me over 15 hours. I later realized, it was not entirely the mistakes of the install process of the software due to which I consumed so much time, but rather the user manual was fairly out-of-date, deceptive and deficient. Overview: • The first and major fault with the document was that it was a “fair weather friend”. If everything operates smoothly, then you rarely need to consult the installation portion. But if some trouble arises, the user manual is ill-equipped to handle it. A quick scan of the Installation part of this manual gives the idea of many users who are having trouble installing the software because they have broken and incomplete installs. • The attempt of the manual to make itself user friendly is actually a drawback for it. It...

Words: 985 - Pages: 4