Premium Essay

Electrical Installation Standards

In: Science

Submitted By 3649885
Words 177034
Pages 709
MINISTRY OF POWER AND MINERAL RESOURCES OF
THE REPUBLIC OF KAZAKHSTAN

APPROVED by Prikaz No 189 of the Minister of Power and Mineral Resources of the Republic of Kazakhstan, as of August 26, 2004.)

REGULATIONS ON ELECTRICAL INSTALLATIONS
OF THE REPUBLIC OF KAZAKHSTAN

(PUE)

Astana, 2003

TABLE OF CONTENTS

SECTION 1: GENERAL REGULATIONS 10

CHAPTER 1.1: GENERAL 10

SCOPE, TERMS AND DEFINITIONS 10 GENERAL REGULATIONS FOR INSTALLATION OF ELECTRICAL EQUIPMENT 11 CONNECTION OF ELECTRICAL INSTALLATIONS TO THE POWER STATIONS 13 COMMISSIONING OF ELECTRICAL INSTALLATIONS 14

CHAPTER 1.2 POWER SUPPLY AND POWER SYSTEMS 14

SCOPE, DEFINITIONS 14 GENERAL REQUIREMENTS 14 CATEGORIES OF POWER CONSUMING DEVICES AND RELIABILITY OF POWER SUPPLY 15 VOLTAGE LEVELS AND CONTROLS, REACTIVE POWER COMPENSATION 16

CHAPTER 1.3 SELECTION OF CONDUCTORS: HEATING, CURRENT DENSITY AND CORONA DISCHARGE CONDITIONS 16

SCOPE 16 SELECTION OF CROSS-SECTION OF CONDUCTORS: HEATING 17 MAXUIMUM CONTINUOUS CURRENTS FOR WIRES, CORDS AND CABLES IN RUBBER OR PLASTIC INSULATION 18 MAXIMUM CONTINUOUS CURRENTS FOR CABLES IN IMPREGNATED PAPER INSULATION 22 MAXIMUM CONTINUOUS CURRENTS FOR BARE WIRES AND BUSES 29 SELECTING CROSS-SECTION OF CONDUCTOR PER THE ECONOMIC CURRENT DENSITY 33 CONDUCTOR CORONA AND RADIO FREQUENCY TESTS 36

CHAPTER 1.4 SELECTION OF ELECTRICAL EQUIPMENT AND CONDUCTORS FOR SHORT CIRCUIT CONDITIONS 36

SCOPE 36 GENERAL REQUIREMENTS 36 IDENTIFICATION OF SHORT-CIRCUIT CURRENTS FOR SELECTION OF EQUIPMENT AND CONDUCTORS

Similar Documents

Free Essay

It Analysis Template

...Exhibit 1: International Standards Agency | Code | Country | Description | ASTM International | E standards (E900-2000) | United States | Photovoltaic cells and module integrity, Develops and delivers international voluntary consensus standards. | CSA International | CSA 107.1 | Canada | Inverter testing | European Solar Test Installation/ESTI | CEC 503 | Italy | Qualification test procedures for crystalline PV modules | European Solar Test Installation/ESTI | CEC 701 | Italy | Qualification test procedures for thin-film PV modules | Factory Mutual | FM Approved | United States | Fire protection tests for solar components | International Electrotechnical Commission | IEC (6)1215 | Switzerland | Design qualification and type approval for crystalline silicon terrestrial PV modules | International Electrotechnical Commission | IEC (6)1646 | Switzerland | Design qualification and type approval for thin-film terrestrial PV modules | International Electrotechnical Commission | IEC 1194 | Switzerland | Characteristic parameters of stand-alone PV systems | International Electrotechnical Commission | IEC 1721 | Switzerland | Resistance to impact test | International Electrotechnical Commission | IEC 1727 | Switzerland | PV characteristics of the utility interface | International Electrotechnical Commission | IEC 1829 | Switzerland | On-site measurement of I-V characteristics of crystalline silicon PV arrays | International Electrotechnical...

Words: 572 - Pages: 3

Premium Essay

The Electrical Genie

...The Electrical Genie Keith L Mayers Jr University of Phoenix The Electrical Genie Customers often have a poor opinion of electrical, plumbing, and HVAC contractors on a broad spectrum of misfortunate incidences. At The Electrical Genie LLC we try our best to reverse the public’s opinion one visit at a time. With a clear vision, a strong mission statement, and an even stronger set of values, our crews at The Electrical Genie are setting new standards in electrical service. In the proceeding, The Electrical Genie will touch on some basic products and services, define the targeted customer base, and product differentiation. In addition, with the creation of a new mission and vision statement; where does The Electrical Genie LLC see it’s self in the future. Define some defining principles or values considering but not limited to culture, social responsibility, and ethics. Analyze how the vision, mission, and values guide the organization’s strategic direction, and evaluate how the organization addresses customer needs and critique how they achieve a competitive advantage. At The Electrical Genie LLC we clearly understand the need for the reinvention of customer support and satisfaction. With a strong back bone of values The Electrical Genie will help your worst electrical disaster disappear like a wish from a Genie. Define your business and the mission statement For the past 10 years Keith L Mayers Jr has been a master electrician with AMTECK Electrical LLC. He is one...

Words: 1403 - Pages: 6

Premium Essay

Electrical Hazards and Safety

...5/3/2014 Electrical Hazards and Safety in Electrical Installations - Research Papers - Kksharma Login Join The Research Paper Factory Join Search Browse Saved Papers Search over 100,000 Essays Home Page » Computers and Technology Electrical Hazards and Safety in Electrical Installations In: Computers and Technology Electrical Hazards and Safety in Electrical Installations Electrical Hazards and Safety in Electrical Installations K K Sharma Lingaya’s University, Faridabad, Email: krishan_ksharma@yahoo.com Abstract: “Electrical Safety is not an option — it is absolutely necessary for workers and employers alike”. Please login to view the full essay... Safety in the workplace is job number one for employer and employee alike. It is especially important for those who install and service electrical systems. Nothing can replace a worker or loved one that has died or suffered the irreparable consequences of an electrical accident. No matter how much an employer tries to safeguard its workers or how much safety training is provided; the ultimate responsibility lies with the worker. The human factor is part of every accident or injury. The purpose of this paper is to identify electrical safety hazards and present ways to minimize or avoid their consequences. It is a guide for improving electrical safety and contains information about governmental regulations, industry-accepted standards and work practices. It presents ways to meet the standards and reduce...

Words: 476 - Pages: 2

Free Essay

Osha Cabling Standars

...(6742); TTY 1-877-889-5627 (or contact OSHA’s area and regional offices during normal business hours.) Federal Registers - Table of Contents | • Publication Date: | 02/14/2007 | • Publication Type: | Final Rules | • Fed Register #: | 72:7135-7221 | • Standard Number: | 1910 | • Title: | Electrical Standard; Final Rule | | | | [Federal Register: February 14, 2007 (Volume 72, Number 30)] [Rules and Regulations] [Page 7135-7221] From the Federal Register Online via GPO Access [wais.access.gpo.gov] [DOCID:fr14fe07-14] ----------------------------------------------------------------------- Part II Department of Labor ----------------------------------------------------------------------- Occupational Safety and Health Administration ----------------------------------------------------------------------- 29 CFR Part 1910 Electrical Standard; Final Rule ----------------------------------------------------------------------- DEPARTMENT OF LABOR...

Words: 91983 - Pages: 368

Premium Essay

Unit 3: Lab 1: Building a New Structure - Nfpa Codes

...as a person and an IT Administrator is to stay safe. History has shown the safety departments about having to write policies which are used to provide recommended practices for the design and installation of safety standards with the Telecommunications infrastructure that will support a wide variety of existing and future services, using industry accepted design and installation methods. To define standards that will enable the design and implementation of structured cabling systems for commercial buildings and between buildings. The telecommunications industry standards, codes and practices are defined in various state and agencies on web sites defined in a catalog that can purchase and downloaded and read for immediate enforcement of these guidelines used for each industry. These policies are intended to answer faxes of infrastructure practices and not to be a substitute for knowledge of industry accepted practices, standards and codes. Policies are not intended to be used in lieu of a construction specification document, are used to abide to the specifications. Communications technologies can be complex and designed and installed by experienced professionals. Telecommunications are considered a fourth utility, to be designed, funded and installed with the same importance as Electrical, Plumbing and HVAC. The designer has the responsibility of providing a design using accepted engineering and architectural practices and recommends a Registered Communications Distribution Designer...

Words: 1394 - Pages: 6

Free Essay

Statement of Work

...and installation services for the project. The furniture supplier shall meet with ARMY North representative to determine the functional and aesthetic requirements for 24 workstations equal to or better than ALUR Panel Based system. It shall provide complete specifications including a detailed floor plan, specific model numbers complete with options and finish designations to satisfy the requirements of the customer. The approximate useable square footage (USF) for each room is as follows: Room 2215A -414 sq ft Chaplain-345 sq ft Room 2023-1240 sqft Room 2032-375 sqft Room 2230B-210 sqft The client agency Point of Contact (POC), also noted as the US Army North Project Manager (PM), will be the liaison at all times between the Furniture Contractor and other stakeholders. The Furniture Contractor will be required to comply with the requirements set forth by the Building Owner. The total number of new workstations is approximately 24. Separate sections in this RFQ package include: Attachment A Statement of Work Attachment B Furniture Typicals Attachment C Pricing Forms Attachment E Furniture Technical Characteristics Compliance Matrix Forms 2.0 GENERAL CONDITIONS 2.0 GENERAL CONDITIONS For any furniture procurement and installation, the contractor shall be responsible for assessing, evaluating, verifying, and confirming the conditions of the building, accessibility, site restrictions, parking, deliveries, loading dock, elevator, storage, installation and staging...

Words: 4893 - Pages: 20

Free Essay

Auxilary Power Units

...aircraft deliveries. Maintenance/repairs will include Honeywell's hydro mechanical units (HMU), avionics, lighting, mechanical components, as well as wheels and brakes, and – it’s Auxiliary Power Units (APU). Aircraft power systems generate, regulate and distribute power throughout an aircraft. These solutions can range from auxiliary power units that provide power when main engines are not running to complete electrical power generation and conversion systems that provide essential power for safe aircraft operation. Honeywell’s robust family of power systems led the industry by lowering cost of operations and increasing reliability. In Air Quality and Comfort in Airliner Cabins, Niren Laxmich and Nagda defines an auxiliary power unit (APU). An APU constitutes: “an engine used to provide aircraft air and electrical power when not provided by the main engines” (Nagda, 2000, p. 261). The following relates information regarding categories of APUs: Category 1 and Category 2 APU The criticality of an APU relative to flight safety in any particular aircraft installation will determine if the APU system should be considered essential, or non-essential. Airplanes that rely on...

Words: 1398 - Pages: 6

Free Essay

How to Choose the Best Electrical Contractor

...How to choose the Best Electrical Contractor Selecting a qualified and competent electrician for your home or business can be an uphill task. This can be even more challenging especially if you don’t know exactly what you want. This is so because you know that there’s a problem but you don’t have the particular know-how to establish the source of the problem. There are specific traits that one should look at when choosing an electrical contractor. First, an electrical contractor should have valid and up-to-date legal documents. This will help in certifying whether the electrician’s practice is recognized by the regulating body. One should make sure that the electrician is licensed to work in the specific geographical area and in the specific field. Secondly, a good electric contractor should be versatile in that he/she is able to adapt to the changing demands of the client. A client may have last minute change of thought thus requiring a change in the electrical fixtures in a particular place which was not initially planned for. Such an electric contractor should be able to offer the pros and cons of changing positions of fittings such that the client arrives at a satisfactory final decision. Experience is also a key factor when looking for the best suited electric contractor. An electrician who has been in the practice over the years has the requisite know-how of handling the different needs of a client. Such an electric contractor will be able to get the job done timely...

Words: 534 - Pages: 3

Free Essay

Fiber Optic Safety and Installation

...Protective Equipment. This term refers to the necessary equipment or goods that will ensure the safety of the individuals installing the wires and the individuals using them later for maintenance and other purposes. This equipment includes helmets, protective clothing, goggles, and other equipment or garment or that is designed for the sake of protecting the workers from injury. • Safe Work Habits The very first step that needs to be taken is to ensure that the optic fiber and copper cables that are about to be installed should comply with all the three requirements that includes the federal regulations, the international standards and the companies requirements. It is also important to wear your PPE and have the proper tools needed for the job. These are the safety rules that need to be followed with fiber optic and copper cable installation: 1. Keep all food and beverages out of the work area. If fiber particles are ingested they can cause internal hemorrhaging 2. Wear disposable aprons to minimize fiber particles on your clothing. Fiber particles on your clothing can later get into food, drinks, and/or be ingested by other means. 3. Always wear safety glasses with side shields and protective gloves. Treat fiber optic splinters the same as you would glass splinters. 4. Never look directly into the end of fiber cables until you are positive that there is no light source at the other end. Use a fiber optic power meter to make certain the fiber is dark. When using...

Words: 2063 - Pages: 9

Free Essay

Sandra Calabrese

...being submitted on October 4, 2015, for Professor Carlos Miranda NT1310 Physical Networking. Building a New Structure – NFPA Codes The FCC issues guidelines that govern the installation of telecommunications cabling and the design of communications devices built or used in the US must follow a code of ethic like local, state, county, city and NEC, and that local codes would take precedence over all other installation guidelines. LPFM stations must protect authorized radio broadcast stations on the same channel or frequency, as well as broadcast stations on first or second-adjacent channels above or below the LPFM station's frequency. This protection would be accomplished through the use of minimum distance separation requirements, which are set forth in 47 CFR 73.807. Second, section 79.2 of the FCC’s rules requires that emergency information provided on television be accessible to individuals who have vision disabilities. This means that broadcasters must describe any emergency information that is shown on the screen, and must accompany any emergency information that is not orally described with an aural tone which instructs individuals with vision disabilities to turn to a radio or another source for more information. The National Fire Protection Association (NFPA) 704 is a standard maintained by the U.S. based National Fire Protection Association. It defines the colloquial "fire diamond" used by emergency personnel to quickly and easily identify the risks posed...

Words: 912 - Pages: 4

Free Essay

Constructing a New Structure- Building Codes

...components or wiring units. The components should also follow certain performance specifications so that when installing we will know exactly what types of applications will be supported. The cable specifications and building codes requirements that we use will be based on * ANSI/EIA/TIA standards 568-C-- Commercial Building Telecommunications Cabling Standard * ANSI/EIA/TIA 569-- Commercial Building Standards for Telecommunications Pathways and Spaces; ANSI/EIA/TIA 606- Administration Standard for the Telecommunications Infrastructure of Commercial Buildings * ANSI/EIA/TIA 607-Commercial Building Grounding and Bonding Requirements for Telecommunications; BICSI Telecommunications Distribution Methods Manual (TDMM) and NFPA 70--National Electric Code (NEC). Cabling has changed over time. Cabling installations have evolved from proprietary systems to flexible, open solutions that can be used by many. (Vendors and applications) A number of documents are related to data cabling. In the United States, the standard is ANSI/TIA-568-C, also known as the Commercial Building Telecommunications Cabling Standard. The ANSI/TIA-568-C standard is a specification adopted by ANSI (American National Standards Institute). If the new building is in...

Words: 2982 - Pages: 12

Premium Essay

Electrical Hazards and Safety in Electrical Installations

...Electrical Hazards and Safety in Electrical Installations K K Sharma Lingaya’s University, Faridabad, Email: krishan_ksharma@yahoo.com Abstract: “Electrical Safety is not an option — it is absolutely necessary for workers and employers alike”. Safety in the workplace is job number one for employer and employee alike. It is especially important for those who install and service electrical systems. Nothing can replace a worker or loved one that has died or suffered the irreparable consequences of an electrical accident. No matter how much an employer tries to safeguard its workers or how much safety training is provided; the ultimate responsibility lies with the worker. The human factor is part of every accident or injury. The purpose of this paper is to identify electrical safety hazards and present ways to minimize or avoid their consequences. It is a guide for improving electrical safety and contains information about governmental regulations, industry-accepted standards and work practices. It presents ways to meet the standards and reduce the hazards. I. Introduction Electricity is very useful and has become essential in modern life. Electric power is used in houses, farms, factories, public places, and commercial establishment and practically in every working place for lighting, operating appliances and machines, heating, cooling, chemical process and transport etc. Electricity is a very good servant but a very dangerous master. Proper...

Words: 5690 - Pages: 23

Free Essay

Exercise Week 2

...with the proper installation of electrical systems and wiring. Knowing this code will help make sure all systems make sure all equipment will be properly installed and lower the risk of fire. The Federal Communications Commission issues guidelines that govern installation of telecommunications cabling and the design of communications devices built or used in the United States. Part 15 of the FCC rules addresses electromagnetic radiation of equipment and cables. It would be important to a new build because you do not want a bunch of hazardous equipment being set up improperly. Underwriters Laboratories, INC is a nonprofit product safety testing and certification organization. If the products installed have a UL mark that means the product has met the UL safety requirements. Using these products on a new build would make sense safety wise. UL 1666 applies to testing flame-propagation height for electrical and optical fiber cables installed in vertical shafts. This test makes sure that the flames will not spread up to another floor. The National Electrical Code article 110.26 calls for a minimum of 3’ to 4’ of clear workspace around all electrical equipment, so that safe operation can be done and maintenance can be performed. This would be used in the new building because it is important that repairs can be done safely if needed. Insulated Cable Engineers Association is an organization that produced cable specifications for telecommunication, electrical power, and control...

Words: 416 - Pages: 2

Free Essay

Physical Networking

...components or wiring units. The components should also follow certain performance specifications so that when installing we will know exactly what types of applications will be supported. The cable specifications and building codes requirements that we use will be based on * ANSI/EIA/TIA standards 568-C-- Commercial Building Telecommunications Cabling Standard * ANSI/EIA/TIA 569-- Commercial Building Standards for Telecommunications Pathways and Spaces; ANSI/EIA/TIA 606- Administration Standard for the Telecommunications Infrastructure of Commercial Buildings * ANSI/EIA/TIA 607-Commercial Building Grounding and Bonding Requirements for Telecommunications; BICSI Telecommunications Distribution Methods Manual (TDMM) and NFPA 70--National Electric Code (NEC). Cabling has changed over time. Cabling installations have evolved from proprietary systems to flexible, open solutions that can be used by many. (Vendors and applications) A number of documents are related to data cabling. In the United States, the standard is ANSI/TIA-568-C, also known as the Commercial Building Telecommunications Cabling Standard. The ANSI/TIA-568-C standard is a specification adopted by ANSI (American National Standards Institute). If the new building is in...

Words: 2980 - Pages: 12

Free Essay

Building a New Structure

...structure on a school campus. A few of those decisions goes towards what wiring and cabling the building will have. There are quite a few codes, standards, and specifications that needs to be followed. Some of those guidelines are NFPA, NEMA, FCC, UL, and NEC. NFPA stands for National Fire Protection Association. NFPA was founded in 1896 as a nonprofit organization to help protect property, people, and the environment from fire damage. It’s now an international organization representing over 100 countries with 65,000 members. NFPA’s mission is to help reduce the risk of fire through safety requirements, research, codes, and fire-related education. NFPA is published every three years. It covers issues related to electrical safety requirements and it’s not used as a design specification or instruction manual. NFPA publishes 300 codes and standards. They are designed to minimize the risk and effects of fire. Its over 200 technical codes-and standard- development committees and is comprised of over 2,000 volunteer seats. The volunteers vote on revision and proposals in a process that is accredited by the ANSI (American National Standards Institute). NFPA also provides free online access to its codes and standards. NEMA stands for the National Electrical Manufacturers Association. NEMA is the association of medical imaging and electrical equipment manufacturers and was founded in 1926. It is headquartered in Rosslyn, Virginia with nearly 400 members. NEMA also has offices in Beijing...

Words: 716 - Pages: 3