Free Essay

Job Sheet Layout

In: Business and Management

Submitted By DannyMcKee26
Words 550
Pages 3
JOB SUMMARY FOR PA TRIP
WEEK OF JULY 11-15, 2011

* Center # 1319 Aston, PA
-Description
* Demo’d Existing kitchen door and Re-installed new Metal Frame and Dutch door w/shelf on lower door.
-Painted Door and frame 2 coats paint to match existing doors in the center.
-Installed Push bolt lock onto Top door to be able to lock door from inside kitchen without access from the outer classroom.
- Had to Mortar (charcoal colored) area of floor around door where 6”x6” tile had to be broken out for door frame removal and installation.
-Put up 2 pieces of 6” Tropical Storm cove base where 6”x6” base tile had to be taken down due to door replacement.
-Man hours on job x 2 = 5 hours
-Drive time to center x 2 = 1 hour

* Center # 303810 Hatboro, Pa
-Description
* Install FRP in 4 restroom’s, install 6” cove (tropical Storm) Demo existing vanities and install new vanities. * FRP’d all restrooms floor to ceiling with cap at the top along the ceiling tile grid. * Installed outside corners as needed around openings in the bathrooms that acted as a stopping point for transition from FRP in the bathroom to the cased opening to the Classroom. * Installed 6” Tropical Storm Cove Base up to the New vanities, and siliconed it to the floor * Installed New Vanities including new traps and new water supply lines, caulked and silicone in and fastened to the wall. * Caulked and silicone as needed inside corners and areas of the FRP. * Total man hours on job x 2 = 49 hours * Total hours loading up & driving to job x 2 = 17 hours

* Center # 301072 Lansdale, PA
-Description
* Demo existing Fascia 1x8 board around right ,left, and rear of bldg. Replace any areas of soffit that are rotted or in bad condition. Paint and caulk in to match. Install Drip Edge to fix shingles around bldg. that are curling over the fascia. * Demo’d 258’ of 1x8” fascia board from rear, right and left side of bldg. Replaced a section of 2”x6”x12’ treated gutter board due to rotted state of existing wood. * Scrapped caulk and removed old nails and staples from gutter board and soffit for installation of new 1x8” cedar boards. * Replaced 258’ of 1x8” cedar fascia board painted 2 coats with safety red. * Installed 2, 8’x 4” strips of ¼” plywood soffit where areas had dry rotted. Painted existing color to match the rest of the soffit, including the lower 1 ½” of the backside of the fascia board to match the existing look of how it was before demo. * Installed drip edge on the right, left and rear side of bldg. total amount installed = 334’ (brown drip edge) Crown stapled with 1” staples on top of the drip edge. * Repaired 3 different sections of plywood where it had popped loose from the trusses and started to bow. Re-nailed the shingles back down and re-sealed them. * Replaced 4 shingles due to tears and tabs missing on them, including a starter shingle. Re-nailed and re-sealed back down. * Removed debri and cleaned area around bldg. where trash and wood had fallen. * Total man hours on job x2 = 29 hours * Total drive time to jobx2 = 1 hour * Drive time to find materials x1= 4.75 hours

Similar Documents

Premium Essay

Unit 714 Assignment 1

...actual name. 1. Where is the layout for the ceiling grid in Room 1002 established? 2. Where size is the projection screen in Room 1010? What must the ceiling installer be aware of when attaching the ceiling to the screen housing? 3. What is the ceiling height in Room 1060? What detail takes precedence over the given ceiling dimension and how should the ceiling height be established for this room? 4. Give the approximate intersecting column lines for the soffit in question for question #3. 5. How is the ceiling to be laid out for Room 1044? 6. What sheet is the enlarged...

Words: 655 - Pages: 3

Premium Essay

Arthur Wilson

...Please do not call or email me and ask for an up dated resume… This is an up to date resume go to http://arthurwilson.vze.com And get a WORD DOC RESUME there. Thank You ARTHUR WILSON CLEVELAND, OHIO Home: (216) 441-3840 Cell : (216) 216 246-6422 Email : arthurwilson3rd@hotmail.com To see sample 3D models and Download Word doc of my resume, please go to my website at http://arthurwilson.vze.com http://www.turbosquid.com/Beta/Search/Index.cfm?keyword=arthurwilson3rd BACKGROUND: Over 20 years of practical work experience and on the job training in the engineering field. Experienced, capable and innovative mechanical designer with record of effective participation and leadership in vitally important and complex projects Demonstrated management competence and broad engineering comprehension by coordinating diverse mechanical engineering ,mechanical design and design drafting disciplines to effect optimum results in adhering to completion schedules and maintaining high quality, safe design and construction relating to the aerospace and defense industry per ANSI-Y-14.5 & DOD-D-100/DOD-STD-1000. EDUCATION: 1980 - 1983 Los. Angeles Trade Technical College Major Course of Study and Details of Classes Mechanical Design Drafting Computer Aided Drafting Tech. Illustration College Level Mathematics Mathematics for engineers ANSI-Y-14.5 Geometric Tolerances and Dimensioning Tolerance analysis and application in design/manufacturing practice. Tolerance...

Words: 3044 - Pages: 13

Premium Essay

Operations Management

...Managing the 5Ps 6 3.1.1 Concept of 5Ps In Operation Management 6 3.1.2 Managing the 5Ps of Operation Management by ETA 7 3.2 Transformation Process 8 3.2.1 Concept of Transformation Process 8 3.2.2 Practice Of Transformation Process In ETA 9 3.2.3 Implication & Analysis On Transformation Process in ETA 9 3.3 Vs Of Operations 11 3.3.1 Concept Of 4Vs in Operations 11 3.3.2 Implications of 4Vs in ETA 12 CHAPTER 4: Process Design 13 4.1 Concept of Process Design 13 4.2 Process Design In ETA 14 4.2.1 Production Process Involved 14 4.2.2 Production Strategies Involved 15 4.3 Implication and Analysis of Process Design in ETA 15 CHAPTER 5: Plant Layout 17 5.1 Concept Of Plant Layout 17 5.2 Plant Layout Used In ETA 17 5.2.1 Cellular Layout 18 5.2.2 Process or Functional Layout 18 5.3 Implications And Analysis of Plant Layout in ETA 18 CHAPTER 6: Capacity Management 19 6.1 Concept Of Capacity Management 19 5.2 Capacity Management In ETA 20 5.3 Implication And Analysis of Capacity Management In ETA 20 CHAPTER 7: Conclusion 21 Reference 22 CHAPTER 1: Executive Summary CHAPTER 2: Company Overview Operation management involves the management of the systems and process that are required to create the goods and/or services. Stevenson (2007) stated that operation management is the management of the part of the organisation that is responsible for producing goods and / or services. Operation management is defined as the design...

Words: 3476 - Pages: 14

Premium Essay

Production Questions

...Date of Submission: November 16, 2015 Lecturer’s Name: Mr. Wynter 1. Discuss the terms Method Study and Work Study in relation to management control procedures. Answer: Method Study: Systematic recording and critical examination of existing and proposed ways of doing work, as a means of developing and applying easier and more effective methods and reducing cost. Advantages include: * Improvement in use of all inputs * Economy in human effort * Layout improvement * Improvement in design of plant and machinery * Improvement in safety standards and procedures * Better working environment Work Study: The systematic examination of the method of carrying on activities so as to improve the effective use of resources and to set up standards of performance for the activities being carried out. Benefits include: * Increased productivity and increased efficiency * Reduced manufacturing costs * Improved work place layout * Better manpower planning and capacity planning * Fair wages to employees 2. Explain the basic production planning and control functions of Loading, Dispatching, Routing Inspection and Corrective Measures. Answer: Production planning may be defined...

Words: 3480 - Pages: 14

Premium Essay

Why Do I Have to Do This

... Exam Mark / 65 Study Score Exam Mark / 65 50 65 39 48 49 64 38 46 48 63 37 44 47 62 36 42 46 61 35 40 45 59 34 38 44 58 33 36 43 56 32 34 42 54 31 32 41 52 30 30 40 50 29 Revising Smart 28 Revising Smart • Make A Definition Sheet Every key term needs a definition Everyday terms you know the definition for, still DEFINE Eg. Organisation, Productivity • • Don’t use the words in the term www.engageeducation.org.au Summary & Definition Sheets Practice Exams Questions from text book Memorising Revising Smart Make A Summary Sheet THE MOST IMPORTANT THING YOU CAN DO BEFORE THE EXAM 1 THE STUDY DESIGN Revising Smart AREA OF STUDIES (5): UNIT 3: • • • AOS1: LSOs in context AOS2: Internal environment of LSOs AOS3: Operations Management Use these dot points as sub-headings for your summary sheets UNIT 4: • • AOS4: Human Resource Management AOS5: Change Management YOUR SUMMARY SHEET Revising Smart Questions from text book Revising Smart 1. Comprehensive Questions – “What”, “List”, “Explain” 2. – – – Analytical Questions How? Synthesize 10 Mark Question Revising Smart Preparing for the 10 Mark Question Preparing for the 10 Mark Question Level of Wastage (PI) Corporate Culture Elements of Operations Function ...

Words: 10141 - Pages: 41

Free Essay

Industrial Engineering

...Prof. S.K.Chakrabarti Mechanical Department, Future Institute Of Engineering And Management | ACKNOWLEDGEMENTS: * To the management & staff at Mondal Enterprises for allowing us into their shop & for their benevolent sharing of information. * To Prof. S. K. Chakrabarti, for giving us a new perspective to engineering by introducing us to such a fascinating topic CONTENTS: No. TOPIC PAGE NO. 1. INTRODUCTION 4 2. OBJECTIVE 5 3. THEORY 5 4. PROJECT DETAILS 10 5. WORK DETAILS 11 6. PROCESSES AND OPERATIONS 12 7. PROCESS CHART 14 8. CALCULATION OF ALLOWANCES 15 9. ALLOWANCE CHART 16 10. CALCULATION OF STANDARD TIME 28 11. FINAL DATA SHEET 30 12. MATERIAL TRANSPORTATION 31 13. LAYOUT PROPOSITION 32 14. CONCLUSION 36 15. BIBLIOGRAPHY 37 INTRODUCTION: Micro, small and medium enterprises (MSME) sector has been recognized as an engine of growth all over the world. The sector is characterized by low investment requirement, operational flexibility, location wise mobility, and import substitution – the perfect conditions for India. Hence, we have vibrant micro and small enterprise sector that plays an important role in sustaining the economic growth, by contributing around 39% to the manufacturing output and 34% to the exports (2004-05). It is also the second largest employer of human resources after agriculture, providing employment to around 29.5 million people (2005-06) in the...

Words: 4932 - Pages: 20

Free Essay

Photoshop

...sophisticated task could take place by itself with the help of computers and robots. During the last 5-6 years there has been a tremendous amount of development in the field of graphics which includes photography, animation etc. So the need for image editing soft wares increased and thus image editing soft wares like Adobe Photoshop, Image ready, GIMP etc were developed. In order to make the job of professional photographers and animators easy and quicker automation was introduced in this field also. With the help of which they could easily edit many images and animation at the same time. . AUTOMATION IN PHOTOSHOP The automate commands simplify complex tasks by combining them into one or more dialog boxes. You can send files directly from the file browser to any of the automation plug-ins that processes multiple images To use an automated command: Choose File > Automate, and then choose any of the commands There are various automate commands available in Photoshop and ImageReady like : 1. Batch 2. PDF Presentation 3. Create Droplet 4. Conditional Mode Change 5. Contact Sheet II 6. Crop And Straighten Photos 7. Fit Image 8. Multi-Page PDF To PSD 9. Picture Package 10. Web Photo Gallery 11. Photo merge In the next few pages these commands are discussed THE BATCH COMMAND The Batch command lets you play an action on a folder of files and subfolders. If you have a digital camera or a scanner with a document feeder, you can also import and process multiple...

Words: 2512 - Pages: 11

Premium Essay

Something

...VEGGIE'S BREAD A Feasibility Study Presented to the Faculty of the Department Of Hotel and Restaurant Management Of the School of Business Management Universidad de Zamboanga In Partial Fulfilment Of The Requirements for the Course of Bachelor of Science in Hotel and Restaurant Management (BSHRM) By: John Paul T. Tolentino Menard S. Gamiao Kirt Ivy Y. Endino Erwin Bryan S. Saavedra August 2015 CHAPTER ONE EXECUTIVE SUMMARY Summary of the Project | Name of the Firm | Veggie’s Bread | Location | Veterans Avenue, Zamboanga, Zamboanga Sibugay, Philippines | Brief Description of the Project | A healthier variety of veggie's breads are what we are in cognizance. For this brand perception that we formalize we would like to linger the interest of the buyers and also the consumer with our version of Veggie Breads. We would like introduce varieties of flavours that consumers that would not normally taste with the following flavours that we would like to propose; Malunggay (horseradish), Ampalaya (bitter gourd). | Project SummaryMarketing Feasibility | | CHAPTER TWO INTRODUCTION Brief background of the Study We make this product proposal for the purpose that we want to serve our valued customers in a new product dishes that we give them a healthy food that will enjoy not only for adults but also for the young ones, we add especial ingredients for our product such as Malunggay (horseradish), We would to introduce varieties of flavours that consumers...

Words: 676 - Pages: 3

Premium Essay

Treysan Prefabricated Steel Cons. Ind. and Trade Corp.

...Production System Analysis In Treysan Prefabricated TREYSAN PREFABRICATED STEEL CONS. IND. AND TRADE CORP. MERVE BUYUKBAS IE 299 October 6, 2013 Industrial Engineering Bilkent University 06800 Ankara Abstract This report is an examination of Treysan Prefabricated Company observed by myself as an intern. In the three stage of the report, firstly, identity of company is defined. Then in the second part, general information is given including the part that the company’s took place in the industry. Conducted system of the company is observed; how they manage the orders from all over the world and how they produced their products are expressed in detail. In the third part, one specific area of the company, Magpan is analyzed and possible outcomes are written in order to develop the existing system.   1   IE299 – Company Identity Card Company Name: TREYSAN Location: Date of Establishment: Ownership: Area (m2) Outdoors: Indoors: Number of Workers White Collar: Blue Collar: Number of IEs: Annual Production Capacity for major products/services KAZAN, ANKARA 1975 IC IBRAHIM CECEN INVESTMENT 32 000 M2 18 000 M2 71 138 7 600 000 M2   2   Treysan Prefabricated Company produces prefabricated panel system buildings, preengineered steel buildings, permanent structures and living containers in its factory in Kazan, Ankara. Treysan Prefabricated is established in Ankara in 1975 by Ibrahim Çeçen and now it continues it’s business as an affiliation...

Words: 3078 - Pages: 13

Premium Essay

Managing People

...The application of these principles will be adhered to as far as relevant, to guarantee the success of the assessment centre. 1.2 Competency-based Assessment The recognition and application of competencies facilitate the assessment centre. A competency can be defined as ‘the ability to perform in a range of work-related activities with the knowledge and understanding required for performance’ (Rogers, 1973). The fundamental driver of a successful AC is in the designer’s ability to draw out the necessary competencies from the job description and person specification to apply them to the task design. 2 ASSESSMENT CENTRE DESIGN 2.1 Job Description 2.2 Person Specification 2.3 Developing Competencies 2.3.1 Stage One: Brainstorming Several key competencies were drawn from the job descriptions and person specifications. ‘Brainstorming’ occurred, as a group, to decide on those competencies that applied to at least one of the individual job descriptions: Oral and Written Communication, Problem Solving, Result Orientation, Interpersonal Skills, Risk Taking, Staff Development, Time Management, Leadership Skills, Flexibility,...

Words: 2113 - Pages: 9

Premium Essay

Help

...Excel 8 Understanding the Interface 10 Using Backstage View 13 Understanding Worksheets 14 Understanding Workbooks 15 Module Three: Your First Worksheet 17 Entering Data 18 Editing Data 20 Using the Wrap Command 21 Adding Rows and Columns 23 Checking Your Spelling 25 Module Four: Working with Excel Files 26 Saving Files 27 Publishing Files to PDF 28 Sending Files via E-Mail 30 Closing Files 31 Opening Files 32 Module Five: Viewing Excel Data 34 An Overview of Excel’s Views 35 Switching Views 36 Creating Custom Views 38 Using Zoom 41 Switching Between Open Files 43 Module Six: Printing Excel Data 44 An Overview of the Page Layout Tab 45 Setting Up Your Page 46 Using Print Preview 48 Printing Data 49 Module Seven: Building Formulas 50 The Math Basics of Excel 51 Building a Formula 52 Editing a Formula 54 Copying a Formula 56 Relative vs. Absolute References 58 Module Eight: Using Excel Functions 59 Formulas vs. Functions 60 Using the SUM Function 61 Using Other Basic Excel Functions 63 Understanding the Formulas Tab 64 Using the Status Bar to Perform Calculations 65 Understanding the New Function Names 67 Module Nine: Using Time Saving Tools 68 Using AutoFill 69 Using AutoComplete 71 Sorting Data 73 Filtering Data 75 Adding Sparklines 80 Module Ten: Formatting...

Words: 3351 - Pages: 14

Premium Essay

Lec2 Material

...CHAPTER 1 What Is Financial Modelling? here are all sorts of complicated definitions of financial modelling, and in my experience there is quite a bit of confusion around what a financial model is exactly. A few years ago, we put together a Plum Solutions survey about the attitudes, trends, and uses of financial modelling, asked respondents “What do you think a financial model is?” Participants were asked to put down the first thing that came to mind, without any research or too much thinking about it. I found the responses interesting, amusing, and sometimes rather disturbing. Some answers were overly complicated and highly technical: n T n n n n “Representation of behaviour/real-world observations through mathematical approach designed to anticipate range of outcomes.” “A set of structured calculations, written in a spreadsheet, used to analyse the operational and financial characteristics of a business and/or its activities.” “Tool(s) used to set and manage a suite of variable assumptions in order to predict the financial outcomes of an opportunity.” “A construct that encodes business rules, assumptions, and calculations enabling information, analysis, and insight to be drawn out and supported by quantitative facts.” “A system of spreadsheets and formulas to achieve the level of record keeping and reporting required to be informed, up-to-date, and able to track finances accurately and plan for the future.” Some philosophical: n “A numerical...

Words: 17366 - Pages: 70

Premium Essay

Information System

...AACS1733 Information Technology and Systems ASSIGNMENT 2010/2011 Objective This coursework aims to provide students an opportunity to explore the use of Microsoft Excel and PowerPoint so as to enhance their understanding of the application software features in spreadsheet and presentation. Grouping This is a group-based assignment. Student may form a group of minimum 4 students and maximum 5 per group (ACCORDING TO ATTENDANCE LIST NAME SEQUENCE). A group leader is to be selected to ensure equal allocation of tasks among each student in the group before assembling a complete assignment report. Plagiarism All work is to be the result of the student's own individual and group effort. Assignment contents are not allowed to be copied from the Internet or from other students. A student who plagiarizes will receive zero point credit on the assignment. Late Policy The assignment should be submitted on the due date stated below unless there is any legitimate reason as to why it is impossible for the student to complete the assignment. As a general rule, no extension of time will be granted. Assignment received after the due date without legitimate reason will be penalized. Submission date: 6/12/2010 (Monday) (Week 11) Assignment return week: Week 14 Assessment This assignment is worth 40% of the overall course assessment. The marks allocations are divided into 2 categories. The first category is an individual mark which is awarded based on each...

Words: 2098 - Pages: 9

Free Essay

Test

...World Wide Web as well as the consolidation of several major players within the industry had radically altered his company’s relative positioning on the competitive landscape. Preparing to celebrate the company’s twentieth anniversary in March 1996, Cha pondered the issues involved in moving Colorscope ahead. Company History Born in Anhui, China in 1938, Andrew Cha immigrated to the United States in 1967 to seek a better life. Originally planning to settle in New York City, where he would pursue his craft as a painter and his wife would attend New York University, his funds ran out in Los Angeles, forcing him to work as a cook and busboy in a downtown Chinese restaurant. Through fortune and hard work, however, Cha eventually found jobs that took advantage of his artistic skills in draftmanship and photography; a succession of promotions within one graphic arts company convinced him that his abilities would enable him to start his own business. Founded on March 1, 1976, Colorscope Inc. was established as a special-effects photography laboratory serving local advertising agencies in southern California. As Cha’s reputation grew, so did the business. Sales increased steadily over the years, peaking in 1988 at $5 million dollars. The company served agency giants such as Saatchi & Saatchi, Grey Advertising, and J. Walter Thompson and large retailing and entertainment companies such as The Walt Disney Company and R. H. Macy & Co. To improve service to these customers...

Words: 3266 - Pages: 14

Premium Essay

Feasibility Study

...FEASIBILITY STUDY OUTLINE 1. The Preliminary Section a. Title Page b. Approval Sheet c. Acknowledgements (if any) d. Table of contents e. List of tables (if any) f. List of Figures (if any) g. List of Annexes/Appendices 2.0 THE EXECUTIVE SUMMARY 3.1 Highlights 2.1.1 Project Background Name of the Proposed project: Type of Business Organization: Location: Proponents: 2.1.2 Management Feasibility Summary 2.1.3 Marketing Feasibility Summary 2.1.4 Technical Feasibility Summary 2.1.5 Financial Feasibility Summary 2.1.6 Socio-Economic Feasibility Summary 2.1 Conclusions (state here, the chances of implementing your project; the advantages of implementing it; and your final analysis and conclusion of the feasibility of your project) 2 Project Background 3.2 Project Proponents Name Address % Ownership 3.3 Proposed Name of the Business/Logo * Here you could state the reason/s four your choice of name or the significance of the name and the logo chosen 3.4 Type of Business Organization * State here if your proposed project is a Single Proprietorship, a Limited or General Partnership, a Corporation, a Subsidiary/Branch/ohers. Indicate the reasons for your choice. 3.4 Location of...

Words: 435 - Pages: 2