...Unit 3 Exercise 1. Specifications – Definitions Application – a system, the transmission method of which is supported by telecommunications cabling, such as 100base-TX Ethernet, or digital voice. Unshielded Twisted Pair – a pair of copper wires twisted together with no electromagnetic shielded around them. Shielded Twisted Pair – a type of twisted-pair cable in which the pairs are enclosed in an outer braided shield, the individual pairs may be shielded as well. Fiber Optic Cable – a cable containing one or more optical fibers Dark Fiber – an unused fiber; a fiber carrying no light, Common when extra fiber capacity is installed Coaxial Cable – a cable that has a single conductor surrounded by insulation and then a layer of shielding that is also a conductor, the two conductor shares one axis. Plenum – the air handling space between the walls, under structural floors, and above drop ceilings when used to circulate and otherwise handle air in the building. Plenum grade cable can be run through these spaces if building codes permit it Riser – a designation for a type of cable run between floors Fire-code rating for indoor cable that is certified to pass through the vertical shaft from floor to floor. Rip Cord – a length of string built into optical fiber cables that is pulled to split the outer jacket of the cable without using a blade Core – the central part of a single optical fiber in which that light signal is transmitted (common sizes are 8.3 microns...
Words: 504 - Pages: 3
...NT 1310 Mr. Davis January 6, 2016 Unit 3 Exercise 1. Specifications – Definitions Application (in terms of cabling infrastructure) – A system the transmission method of which is supported by telecommunications cabling, such as a 100base-TX Ethernet, or digital voice. Unshielded Twisted-Pair – (UTP) a pair of copper wires twisted together with no electromagnetic shielding around them. Each wire pair is twisted many times per foot to cancel out electrical signal. Shielded Twisted-Pair – A type of twisted pair cable in which the pairs are enclosed in an outer braided shield, although individual pairs may also be shielded. Fiber-Optic Cable - An optical fiber cable is a cable containing one or more optical fibers. The optical fiber elements are typically individually coated with plastic layers and contained in a protective tube suitable for the environment where the cable will be deployed. Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two Dark Fiber – Dark fiber refers to unused fiber-optic cable. Often times’ companies lay more lines than what’s needed in order to curb costs of having to do it again and again. The dark strands can be leased to individuals or other companies who want to establish optical connections among their own locations. Coaxial Cable - is a type of cable for high bandwidth data transmission use that typically consists of a single copper wire...
Words: 927 - Pages: 4
...Unit 3: Introduction to Marketing Unit code: Y/502/5411 QCF Level 3: BTEC National Credit value: 10 Guided learning hours: 60 Aim and purpose The aim and purpose of this unit is to give learners an understanding of how marketing, research and planning and the marketing mix are used by all organisations. Unit introduction Marketing is at the heart of every organisation’s activity. Its importance is also growing in the non-commercial, public and voluntary sectors. Also, at the heart of marketing is the customer. This unit will introduce learners to some of the tools and techniques all types of organisations use to achieve their objectives. Firstly, learners will explore how different types of organisations use marketing principles to meet the needs of their customers and achieve their objectives. The constraints under which organisations operate are important and learners will study the legal requirements and voluntary codes that affect marketing. Learners will then go on to investigate how organisations collect data through market research and turn it into useful information which can be analysed and used to plan their marketing activities. The segmentation and targeting of groups of customers is a key marketing technique and this is studied in detail. This includes the different bases for segmentation of both consumer and business markets. Next, learners will examine how a marketing mix is developed to meet the needs and aspirations of...
Words: 4051 - Pages: 17
...Course Package Bring this document with you each week Students are required to complete each assignment and lab in this course package on time whether or not they are in class. Late penalties will be assessed for any assignments or labs handed in past the due date. The student is responsible for replacement of the package if lost. Table of Contents Syllabus 2 Student Professional Experience 19 Graded Assignments and Exercises 23 Labs 47 Documenting your Student Professional Experience 57 ITT Technical Institute NT1310 Physical Networking Onsite Course SYLLABUS Credit hours: 4.5 Contact/Instructional hours: 56 (34 Theory Hours, 22 Lab Hours) Prerequisite(s) and/or Corequisite(s): Prerequisites: NT1210 Introduction to Networking or equivalent Course Description: This course examines industry standards and practices involving the physical components of networking technologies (such as wiring standards and practices, various media and interconnection components), networking devices and their specifications and functions. Students will practice designing physical network solutions based on appropriate capacity planning and implementing various installation, testing and troubleshooting techniques for a computer network. Where Does This Course Belong? | | | NT2799 | | | | | | | | NSA Capstone | | | | | | | Project | | | | | NT2580 | | | NT2670 | NT2640 | | PT2520 | | Introduction to | | | | |...
Words: 10839 - Pages: 44
...Victor Lau B.Sc., M.Sc., MHKIS, MRICS 28 February 2006 COST PLANNING & COST ESTIMATE • DEFINITIONS, TERMS & PROCESSES • TYPES OF PRE-CONTRACT COST PLANNING • FACTORS AFFECTING COST ESTIMATES/PLAN 2 DEFINITIONS, TERMS & PROCESSES A. Classification of Areas B. Terms of Cost Estimate & Cost Plan C. Pre-Contract Cost Planning Processes 3 DEFINITIONS, TERMS & PROCESSES A. CLASSIFICATION OF AREAS GROSS FLOOR AREA (GFA) GFA is the area contained within the external walls of the building measured at each floor level (including any floor below the level of the ground), together with the area of balconies and the thickness of external walls (for submission to Planning Authorities) Note : Carpark & plant room areas are usually excluded, but this is NOT a fixed rule CONSTRUCTION FLOOR AREA (CFA) CFA is the covered areas fulfilling the functional requirements of the building measured to the outside face of the external walls or external parameter. Areas occupied by partitions, columns, internal structural walls, bay windows, stairwells, lift shafts, plant rooms, water tanks, carparks, open covered areas and the like are included. 4 DEFINITIONS, TERMS & PROCESSES B. TERMS OF COST ESTIMATE & COST PLAN ELEMENTAL QUANTITY • No. of door • Area of wall finishes • Volume of concrete structure • Elemental quantity per CFA (i.e. Element Quantity / CFA) • Average cost per unit elemental quantity (i.e. Total Cost of Element / Elemental Quantity) • Indication of price...
Words: 1428 - Pages: 6
...For first teaching from September 2006 Issue 2 March 2007 Specification Edexcel Level 2 BTEC First Certificate and Edexcel Level 2 BTEC First Diplomas in Sport Edexcel, a Pearson company, is the UK’s largest awarding body offering academic and vocational qualifications and testing to more than 25,000 schools, colleges, employers and other places of learning here and in over 100 countries worldwide. We deliver 9.4 million exam scripts each year, with 3 million marked onscreen in 2005. Our qualifications include GCSE, AS and A Level, GNVQ, NVQ and the BTEC suite of vocational qualifications from entry level to BTEC Higher National Diplomas and Foundation Degrees. We also manage the data collection, marking and distribution of the National Curriculum Tests at Key Stages 2 and 3, and the Year 7 Progress Tests. References to third party material made in this specification are made in good faith. Edexcel does not endorse, approve or accept responsibility for the content of materials, which may be subject to change, or any opinions expressed therein. (Material may include textbooks, journals, magazines and other publications and websites.) Authorised by Jim Dobson Prepared by Dominic Sutton Publications Code BF017349 All the material in this publication is copyright © Edexcel Limited 2007 Essential principles for delivering a BTEC This specification contains the rules and regulations along with the units and associated guidance to enable centres to deliver a programme...
Words: 53621 - Pages: 215
...Networking GRADED ASSIGNMENTS ------------------------------------------------- Student Professional Experience Project NSA SPE Project 1 (to be completed by the end of NT1310): Install, Configure, Test, Maintain and/or Document the Worksite Local Area Network and Its Components Purpose The purpose of the Student Professional Experience (SPE) project is to provide you an opportunity for work experience in your field or in a related field to add to your résumé. You may have an opportunity to serve your community or work for a local employer for a project that will take between 20 and 30 hours. Project Logistics Career Services will identify an employer with needs in the following areas: Network related tasks (mostly confined to the LAN and Microsoft Windows Server 2008 environments) Students are expected to practice various skills discussed in all the technical courses in Quarters 1 through 3 of the NSA program at an employer’s site on network related tasks (more confined to the LAN and Microsoft Windows Networking with Server 2008 environments) that would involve installation, configuration, testing, maintenance and documentation of the worksite network and its components, and to properly document the technical information in all involved activities. Such documentation will be used as the source material for Items 2 and 3 defined in the Deliverables section of this document. Possible example projects could be (but are not limited to): Install/maintain/upgrade...
Words: 6762 - Pages: 28
...CMIS 102 Hands-On Lab // Week 3 Overview: This hands-on lab allows you to follow and experiment with the critical steps of developing a program including the program description, analysis, test plan, design (using both flow chart and pseudocode visualization), and implementation with C code. The example provided uses sequential and selection statements. Program Description: This program will calculate the area of a right triangle. The program will ask the user to enter the base and height and then use these values to calculate and then print the area of the triangle. If the area of the triangle is greater than 100 square units, an additional message is printed stating the triangle is too large for the specification. However; if the triangle is less than or equal to 100 square units, the additional message will state the triangle is within specifications. The design step will include both pseudocode and flow chart visualization. Analysis: I will use sequential and selection programming statements. I will define two float numbers for the base and height: base, height. Float numbers were selected as opposed to integers to make sure triangles of all dimensions are possible and not just whole numbers. Float number will store the area: area The area will be calculated by this formula: Area = ½ * (base * height) For example if the base was 4.2 and the height was 5.3 the area would be calculated as: Area = ½ * (4.2 * 5.3) = ½ * (22.26) = 11.13 The additional selection...
Words: 723 - Pages: 3
...Semester Period Unit No 103 Units Covered Unit Name Further Mathematics for Engineering Technicians Electrical and Electronic Principles Data Communications and Networks Analytical Methods for Engineers Engineering Science Telecommunication Principles Advanced Mathematics for Engineering Electrical and Electronic Principles Business Management Techniques for Engineers Computer Programming Techniques Radio Communication Engineering Electronic Principles Principles and Applications of Microcontrollers Digital and Analogue Devices and Circuits Management of Projects Project Design, Implementation and Evaluation Personal and Professional Development Work-based Experience Credit Hours 10 10 15 15 15 15 15 15 15 15 20 15 15 15 15 20 15 15 Unit Level 3 3 4 4 4 5 5 5 4 4 4 5 4 5 5 5 5 5 Semester 1 (10 weeks) September- November 2014 101 119 001 Semester 2 (10 weeks) December- February 2014 002 118 059 Semester 3 (10 weeks) March - May 2014 005 007 112 Semester 4 (10 weeks) June - August 2015 120 039 113 Semester 5 (10 weeks) September-November 2015 117 037 Semester 6 (10 weeks) 003 December 2015 -February 2016 027 029 Industrial Training March 2016 - September 2016 UNIT 1: ANALYTICAL METHODS FOR ENGINEERS Unit 1: Unit code: QCF level: Credit value: Analytical Methods for Engineers A/601/1401 4 15 • Aim This unit will provide the analytical knowledge and techniques needed to carry out a range of engineering...
Words: 26988 - Pages: 108
...| Unit 3. Exercise 1. | | Specifications - Definitions | | Unit 3. Exercise 1. | | Specifications - Definitions | NT1310: physical networking April 15, 2014 Authored by: Nicholas Rapisardi NT1310: physical networking April 15, 2014 Authored by: Nicholas Rapisardi 1. Application (in terms of cabling infrastructure): The application layer is the OSI layer closest to the end user, which means both the OSI application layer and the user interact directly with the software application. When determining resource availability, the application layer must decide whether sufficient network or the requested communication exists.. (OSI_model#Layer_7:_application_layer) 2. Unshielded twisted-pair: UTP cable is a popular cable used in computer networking that consists of two shielded wires twisted around each other. In the image to the right, is an example of the different network cables you're likely to encounter. (/jargon/u/utpcable.htm) 3. Shielded Twisted-pair: Twisted Pair (STP) has a fine wire mesh surrounding the wires to protect the transmission; Unshielded Twisted Pair (UTP) does not. Shielded cable is used in older telephone networks, network, and data communications to reduce outside interference. In the picture to the right, is an example of what these cables look like inside. (jargon/t/twispair.htm) 4. Fiber-Optic cable: A fiber optic cable is a network cable that contains strands of glass fibers inside an insulated casing. These...
Words: 1317 - Pages: 6
...Unit 3. Exercise 1. Specifications – Definitions Course Objectives and Learning Outcomes In this Exercise, you will define important specification terms. Assignment Requirements Define the following terms: • Application (in terms of cabling infrastructure)- The word application, in terms of cabling infrastructure, often refers to information technology. The infrastructure itself could be a city, nation, or corporation. • Unshielded Twisted-Pair- Unshielded twisted pair is the most common kind of copper telephone wiring. Twisted pair is the ordinary copper wire that connects home and many business computers to the telephone company • Shielded Twisted-Pair- Shielded twisted pair is a special kind of copper telephone wiring used in some business installations. An outer covering or shield is added to the ordinary twisted pair telephone wires; the shield functions as a ground. • Fiber-Optic Cable- is a cable containing one or more optical fibers that are used to carry light • Dark Fiber- cable that's already been laid, but is not yet in use. • Coaxial Cable- s a type of cable that has an inner conductor surrounded by a tubular insulating layer, surrounded by a tubular conducting shield • Plenum- is cable that is laid in the plenum spaces of buildings • Riser- Cable that is run between floors in non-plenum areas is rated as riser cable • Rip Cord- containing one or more optical fibers that are used to carry light. • Core- is a cylinder of glass or plastic that runs...
Words: 344 - Pages: 2
...Table of Contents page no. 1. EXECUTIVE SUMMARY 1-2 2. INTRODUCTION 3-7 * PHARMACEUTICAL INDUSTRY IN INDIA 4 * FACTS ABOUT INDIAN PHARMACEUTICAL COMPANY 5-6 3. COMPANY PROFILE 7-12 * HISTORY 8-9 * VALUES, VIEW AND POSITION 10 * RESPONSIBILITY 11 * DISCOVERY AND DEVELOPMENT 12 4. COMPENETCY MAP 13-18 5. HUMAN RESOURCE DEPARTEMENT 19 ...
Words: 8260 - Pages: 34
...N14C31 Managing Projects 01.10.2012 Lecture 1: Introduction to Project Management & WBS Dr Christos Braziotis Christos.Braziotis@nottingham.ac.uk Module Convenor Dr Christos Braziotis Lecturer in Supply Chain and Operations Management Nottingham University Business School, Room B37, South Building Tel: 115 9514026 Email: Christos.Braziotis@nottingham.ac.uk N14C31 – Managing Projects © Christos Braziotis, 2012-2013 – Nottingham University Business School Slide 2 Agenda • Introduction to the Module: – Aims – Resources – Assessment • Introduction to Project Management: – Aspects to consider in Project Management – Work Breakdown Structure N14C31 – Managing Projects © Christos Braziotis, 2012-2013 – Nottingham University Business School Slide 3 Introduction to Project Management N14C31 – Managing Projects © Christos Braziotis, 2012-2013 – Nottingham University Business School Slide 4 • The word “Project” is frequently used N14C31 – Managing Projects © Christos Braziotis, 2012-2013 – Nottingham University Business School Slide 5 • The word “Project” is frequently used N14C31 – Managing Projects © Christos Braziotis, 2012-2013 – Nottingham University Business School Slide 6 What is a Project? – Definitions • A temporary endeavor undertaken to create a unique product or service (US Project Management Institute) • Unique process, consisting of a set of coordinated and controlled activities with start and...
Words: 3914 - Pages: 16
...printed version. © OCR 2008 QAN 500/2591/0 QAN 500/2587/9 Contents 1 About these Qualifications 4 1.1 6 The Four-Unit Advanced GCE 6 1.3 Qualification Titles and Levels 6 1.4 Aims 7 1.5 2 The Two-Unit AS 1.2 Prior Learning/Attainment 8 9 2.1 AS Units 9 2.2 3 Summary of Content A2 Units 10 12 3.1 AS Unit G451: An introduction to Physical Education 12 3.2 AS Unit G452: Acquiring, developing and evaluating practical skills in Physical Education 24 3.3 A2 Unit G453: Principles and concepts across different areas of Physical Education 31 3.4 4 Unit Content A2 Unit G454: The improvement of effective performance and the critical evaluation of practical activities in Physical Education 55 62 4.1 AS GCE Scheme of Assessment 62 4.2 Advanced GCE Scheme of Assessment 63 4.3 Unit Order 64 4.4 Unit Options (at AS/A2) 64 4.5 Synoptic Assessment (A Level GCE) 64 4.6 Assessment Availability 64 4.7 Assessment Objectives 65 4.8 5 Schemes of Assessment Quality of Written Communication 66 Technical Information 67 5.1 Making Unit Entries 67 5.2 Making Qualification Entries 67 5.3 Grading 68 5.4 Result Enquiries and Appeals 69 5.5 Shelf-Life of Units 69 5.6 Unit and Qualification Re-sits 69 5.7 Guided Learning Hours 69 5...
Words: 22885 - Pages: 92
...2007-08 with MQP Page 1 of 16 Annexure No. SCAA Dated BHARATHIAR UNIVERSITY, COIMBATORE – 641 046 M. Sc COMPUTER SCIENCE For School of Distance Education (Effective from the academic Year 2007-2008) Scheme of Examinations 31 J 29.02.2008 Year Subject and Paper I Paper I Paper II Paper III Paper IV Practical I Paper V Paper VI Paper VII Practical II Project Advanced Computer Architecture Computer Graphics & Multimedia Software Engineering Computer Networks Computer Graphics and Multimedia Lab Advanced Operating System Internet programming and Web Design Data Mining and Warehousing Internet programming and Web Design Lab Project Work and Viva Voce Total University Examinations Durations Max in Hrs Marks 3 100 3 100 3 100 3 100 3 100 3 3 3 3 100 100 100 100 100 1000 II For project work and viva voce (External) Breakup: Project Evaluation : 75 Viva Voce : 25 1 Anx.31 J - M Sc CS (SDE) 2007-08 with MQP Page 2 of 16 YEAR – I PAPER I: ADVANCED COMPUTER ARCHITECTURE Subject Description: This paper presents the concept of parallel processing, solving problem in parallel processing, Parallel algorithms and different types of processors. Goal: To enable the students to learn the Architecture of the Computer. Objectives: On successful completion of the course the students should have: Understand the concept of Parallel Processing. Learnt the different types of Processors. Learnt the Parallel algorithms. Content: Unit I Introduction to parallel...
Words: 3613 - Pages: 15
