Free Essay

Unit 5 Lab

In: Computers and Technology

Submitted By willmo83
Words 341
Pages 2
When installing cables there are several factors to consider: cost, future expansion, bandwidth, signal strength, and EMI. Each type of cable has different specifications that affect these installations and every job will have different needs associated with those factors. When working on a worksite there are a few tools you will need; such as cable pulleys, punch downs, wire cutters, and cable strippers. You will need most of these tools to install your cable into your building. For preexisting buildings you will need different style tools to complete your job. You may need a fish tape or fiberglass push pole it really depends on the type of job you are going to be doing and what type of cable or fiber you are going to be working with. This will determine what tools you will need to get the job done correctly and safely.
Before you begin the first thing you will need is a plan on how to perform your task. Without this there will only be confusion and pain for you. Next you will need to know what the customer needs which cable or fiber you’re going to be installing. After that you will need to know distance from your leased line to your routers and which cable you will need for your backbone and horizontal lines. Safety is the most important thing to remember in this job field. Working with electricity and working aloft will get you killed in a hurry or seriously injured. After all the work is done clean up and make sure the job is done properly and works without fail. There is nothing more time consuming and costly that improper performance when working with cabling.
My makeshift tool would have to be my cigarette lighter. Too heat up copper wire to make it flexible. To see in the dark, and too warm up tools to help get dirt off of old terminals. It was the most useful tool I’ve ever had and there are so much more applications it could be used in.

Similar Documents

Premium Essay

Unit 5 Lab 1

...Physical Networking Unit 5 Lab 1 Wired and Wireless Networks The biggest difference between these two types of networks is one uses network cables and one uses radio frequencies. A wired network allows for a faster and more secure connection and can only be used for distances shorter than 2,000 feet. Several other disadvantage of a wired network such as the “need to run cables in difficult environments through walls, floors and ceilings. Cables need to be run from computer to computer and switch to switch. Process can be time consuming. Loose cables likely remain the single most common and annoying source of failure in a wired network.” (PACE University, n.d.) While a wireless network is a very useful and convenient networking device, however these types of networks a lot less secure and transmission speeds can suffer from outside interference. Although wireless networking is a lot more mobile than wired networking the range of the network is usually 150- 300 indoors and up to 1000 feet outdoors depending on the terrain. The cost for wired networking has become rather inexpensive. Ethernet cables, hubs and switches are very inexpensive. Broadband routers cost more, but these are optional components of a wired network, and their higher cost is offset by the benefit of easier installation and built-in security features. The primary parts of a wired network are the cables, network adapters, and routers. Wired...

Words: 315 - Pages: 2

Premium Essay

Unit 5 Lab 1

...Wired and Wireless Networks ITT Technical Institute Physical Networking – NT1310 11/10/2014 Wired and Wireless Networks The biggest difference between these two types of networks is one uses network cables and one uses radio frequencies. A wired network allows for a faster and more secure connection and can only be used for distances shorter than 2,000 feet. Several other disadvantage of a wired network such as the “need to run cables in difficult environments through walls, floors and ceilings. Cables need to be run from computer to computer and switch to switch. Process can be time consuming. Loose cables likely remain the single most common and annoying source of failure in a wired network.” (PACE University, n.d.) While a wireless network is a very useful and convenient networking device, however these types of networks a lot less secure and transmission speeds can suffer from outside interference. Although wireless networking is a lot more mobile than wired networking the range of the network is usually 150-300 indoors and up to 1000 feet outdoors depending on the terrain. The cost for wired networking has become rather inexpensive. Ethernet cables, hubs and switches are very inexpensive. Broadband routers cost more, but these are optional components of a wired network, and their higher cost is offset by the benefit of easier installation and built-in security features. The primary parts of a wired network are the cables, network adapters, and routers. Wired...

Words: 1042 - Pages: 5

Premium Essay

Nt1310 Unit 5 Lab

...Graph 5 illustrates the relationship between the enzyme parameters of the Michaelis–Menten equation. This equation is represented in equation 3 below. The plot was supposed to be a smooth curve but an error occurred, so the velocity of tube 8 was lower than expected. Tube 8 and tube 9 had the same concentration of substrate, so the velocity of tube 8 should have been the same as the velocity of tube 9. The velocity of tube 9 was 26.296μmoles/liter/min. This error could have been due to the wrong about of enzyme or ONPG added to the tube. The wrong amount of ONPG can be easily added to the tube since too many tubes were set up at the same time. Taking time and carefully adjusting the pipet can prevent this error from occur. Other possible errors...

Words: 614 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab

...Before the lab began, a box with 2” styrofoam on the bottom and all sidewalls was created. A 2” styrofoam top with a small wooden part for additional cover was added. A lightbulb of unknown wattage was placed inside of the box and was turned on for an unknown time. A small hole was cut into one sidewall in order to place thermocouple probes into at a later time. The first portion of this lab was to set up the initial thermocouple setup, which was described in the apparatus section of this report. Project 7-A: After the apparatus was was set up, thermocouple probe tip voltage was recorded using NI DMM Soft Front Panel software. Voltage relating to ambient temperature was also recorded. Using the provided thermocouple tables and the law of intermediate temperatures, the temperature in the box was found....

Words: 430 - Pages: 2

Free Essay

Unit 5 Lab 5.1-5.4

...Unit 5. LAB 5 Ethernet LANs LAB 5.1: LAN Standard Exercise 5.1.1 Briefly define the 802.1 standard: Keeper of the LAN architecture – IEEE standard 802. Describes the 802 family of standards. Describes the LAN Architecture. Defines some useful things, such as the LAN address format, the SNAP protocol, the Playpen Ethertypes, and the OID registration arcs. The higher Layer Interface working group in 802. Defines the bridging and security glue that interconnects the LANs define by the 802 MAC groups. Exercise 5.1.2 What 802.3 standard originally define PoE functionality? When was the standard enhanced, and what was the new standard name given for the enhancement? The standard that originally defines PoE functionality was the IEEE 802.3af. The new standard is known as IEEE 802.3at it, and it was enhanced in 2012. Exercise 5.1.3 Complete Table Standard | Cabling | Maximum Length | 10BASE5 | Coaxial(Thicknet) | 500m | 10BASE2 | Coaxial (Thinnet) | 185m | 10BASE-T | UTP (Cat3, 5, 5e, 6) | 100m | 100BASE-FX | Multi-mode fiber optic cable (SC or ST) | 400m | 100BASE-T | UTP (Cat3, 5, 5e, 6) | 100m | 100BASE-T4 | STP Twisted Cable | 100m | 100BASE-TX | Single-mode fiber optic cable | 20km | 1000BASE-LX | SMF and MMF | 550m | 1000BASE-SX | MM fiber-optic | 220m or 550m (dependent upon fiber thickness | 1000BASE-ZX | MM fiber-optic | 550m | 1000BASE-T | UTP (Cat3, 5, 5e, 6) | 100m | Exercise 5.1.4 What does the numeric prefix before BASE in the Ethernet...

Words: 1936 - Pages: 8

Premium Essay

Nt1310 Unit 5 Lab Report

...The single-phase induction motor can successfully be driven from a variable frequency power supply. Hence, the motor speed can be easily adjusted. The torque performance of the capacitor- connected motors can be enhanced at low frequency range by altering the V/f control law such that the internal power dissipation in the motor is held constant. VFD control provides efficient speed control the speed is controlled by varying the frequency not the stator voltage. The power factor is improved and the harmonic distortions were less. The simulation of a Modified SEPIC PFC converter fed induction motor drive is done using MATLAB. MATLAB is a high performance language for technical computing. It integrates computation, visualization and programming in an easier environment where problems and solutions are expressed in familiar mathematical notation. MATLAB is specially designed simulation software for power electronics and motor drive. By using MATLAB, various converter configurations can be modelled and compared. 4.1 Open Loop control Fig 4.1 Open loop control of Modified SEPIC converter Input voltage of 230V is given to the Modified SEPIC PFC Converter so that an output voltage of 400V DC is obtained. The input current waveform is of pure sinusoidal. Fig 4.2 Input Current Waveform Fig 4.3 Output Voltage Waveform Power factor of 0.98 above is obtained using the open loop control of the Modified SEPIC PFC converter. 4.2 Closed Loop Control Fig 4.4 Closed Loop Control...

Words: 658 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab Report

...crossover gives genetic algorithm much of their power. With crossover, beneficial mutations on two parents can be combined immediately when they reproduce. Mutation, on the other hand, randomly changes a bit in an individual from 0 to1 or vice versa, thereby introducing new material into the knowledge base. This operator is assigned a very low percentage of activation, causing it to function as a background operator. Figure 4 4 Two-point crossover Figure 4 5 Mutation Comparison of optimization strategies This study is not a comparative study of search and optimization techniques. Nonetheless, it is important to question whether GA is the best choice for this study. David E (1989) identifies three main types of search strategies: calculus-based, random, and enumerative as known as heuristic approaches. (See Figure 4-1) The methods can be applied depending on the type of the function one wants to optimize. In the following sub section, several different sorts of strategies will be explained. Figure 4 5 different optimization strategies Hill climbing strategy Hill climbing strategy is one of calculus-based strategies and is the intuitive method any wanderer would use to reach the peak of a mountain in a dense fog: always walk uphill. In the calculation process, the program seeks local optima by hopping on the function and moving in a direction related to the local gradient. The major problem with hill climbing is that the result strongly depends on the starting point...

Words: 1455 - Pages: 6

Premium Essay

Nt1310 Unit 5 Lab Report

...1.5.1.1 Incandescent Lamp A tungsten filament bulbs were used to performed and verified the effect of voltage variations on the performance and efficiency of the lighting lamp. From the experimental setup, it was showed that the lamps (incandescent lamps) consumes more energy at higher voltages; as the voltage increase, the lamp brightness (intensity) increases. Similarly, as the voltage decreases the lamps brightness appear dim. It should worth saying here that as the brightness increase at a higher voltages, so it consumes more energy and it may lead to a shorter lifespan of the lamp. One of the foremost effect of voltage variations on the incandescent lamp was lamp flicker. Lamp flicker is an effect on a lamp brightness in which there is rapid visible changes or variations of the intensity or brightness level for the incandescent lamp. The fluctuations in the brightness or intensity of the lamps causes inconvenience or discomfort to the utility consumers. 1.5.1.2 Computer From the experimental setup, it was clearly showed that the computer (Laptop) consumes a constant power with voltage variations. As the voltage varies with the corresponding variation in current at 70volts, the laptop was still consuming the same power but one effect is noticed with the charger becoming hotter showing high current presences at the time of very low voltage which can damage the charger overtime. 1.5.1.3 Television The CRT (Cathode Ray Tube) television of 34cm, 14'' was used for this experimental...

Words: 700 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab Answers

...ANSWER THE FOLLOWING QUESTIONS (ignore questions in lab manual) 1) Describe clearly and precisely the function of a positive control. 2) Describe the function of a negative control. What conclusions you would make about your entire experiment if the negative control did not act accordingly? 3) What might you conclude about the results of your test samples if one or more of the test samples tested positive but the positive control did not work according to plan? 4) What tubes represent the positive control and negative controls in Procedures 3.1, 3.2, 3.3 and 3.4? 5) Procedure 3.1 step 11 Optional treatment (see exercise in this pdf) asked you to include a tube containing a known reducing sugar and Benedict’s reagent while omitting heat. What was...

Words: 590 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab Report

...CHAPTER 6 SIMULATION RESULTS 6.1 Introduction The passive filters were designed according to the specifications of Table 2. The precharge method and the pre-charge sequence are an important and not trivial design step of the iUPQC due to the power flow characteristics of the system. During the start-up, the voltage supplied to the load cannot be distorted, and the iUPQC coupling in the circuit shall not affect the load. The pre-charge method developed allows the start-up of the iUPQC with no need of load power disconnection. The used pre-charge sequence is shown in Fig. 6.1.The pre-charge circuit has three contactors, namely, Ks, Kp, and Kp2, and one in-rush resistor Rpc. The switches sw1 and sw2are used symbolically to show the switching turn-on time. The Kp1 and Kp2 contactors are initially opened, while the Ks contactor is initially closed, and the switching of both active filters is initially disabled. Fig 6.1 Precharge sequence of the iUPQC The pre-charge sequence starts when the contactor Kp1 is turned on, providing the charge of the dc link capacitors through antiparallel diodes present in the PAF power circuit. After 340 ms, the switching of the SAF sw1 is enabled, causing a voltage unbalance on the dc link during a short period of time due to the stabilization time of the SAF unbalanced-voltage control loop. After 1s, the Ks contactor is turned off, allowing the increase of the dc link voltage by SAF operation. After 10 ms, the switching of the PAF sw2 is enabled, starting...

Words: 772 - Pages: 4

Premium Essay

Nt1310 Unit 5 Lab Report

...To begin the voltage measurement procedure, we made sure that the DC Power supply cables (positive and negative) were plugged into the power supply source so we could obtain a precise and accurate measurement. After we secured our cables into our power supply, we turned our power supply source on. We discovered that it was not directly plugged into the electrical outlet, so we connected it to the outlet and the digital numbers on the power supply appeared. Our next step was to tune the power supply’s current knob to barely above the 0 value, this gave us a minimal amount of potential electrons in our cable. When our current knob was perfectly tuned, we began to adjust our voltage knob to 6.5 volts. Obtaining the 6.5 volts on the power supply was a bit tedious. We had to be extremely delicate with the knob to acquire the 6.5 volt reading. After minutes of adjusting, the 6.5 volt reading finally appeared. In order to check and see if the power supply source was revealing an accurate reading, we turned on the digital multimeter and adjusted the switch to DC voltage. We connected both sets of cables from each device. For the first measurement, our reading was almost 100% percent accurate. We obtained 6.431 volts which was almost perfect. Since we got off to a fast start we went ahead and calculated the percent error for our measurements. We calculated a 1.1% error. To continue the experiment, we went ahead and repeated the same procedure but adjusted the volt knob to...

Words: 539 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab Report

...Amazon 5 Bullet Points: ELIMINATE CONFUSION: Conveniently manage pills for the entire week MULTIPLE DIVIDERS: Each tray has four sections for morning, noon, evening and bedtime COLOR-CODED DAYS: Each day has a designated color to eliminate missed pills COMPACT DESIGN: Pill tower is compact for use at home, at work or while traveling CONVENIENT PILL SPLITTER: Easy to use pill splitter is also included Product Description: Organize and manage pills easily and efficiently with the Vive plastic pill organizer. Conveniently manage medications and supplements with the easy to use Vive pill organizer. The durable plastic pill box contains seven color-coded trays with sliding lids, one for each day of the week. Each tray is divided into four compartments:...

Words: 774 - Pages: 4

Premium Essay

Nt1310 Unit 5 Lab Report

...This was the circuit’s input voltage. The Tektronix TDS 2014B oscilloscope was then used to verify the accuracy of the output wave by making sure that the amplitude was 10V peak-to-peak, with a frequency of .5 Hz and a mean value of zero. Subsequently, this square wave was then applied to the input of the RC circuit. The functionality of the circuit was also verified when the left two LEDs lit up in pairs and then right two LEDs lit in pairs successively. SignalExpress was used to record and graph the input of the system, which was a square wave, and the output of the RC circuit. This graph verified the functionality of the of circuit and also aided in calculating the time constant of the system. Next, the circuit was modified by a adding another 0.1 μF capacitor in parallel to the first capacitor and by replacing the 470kΩ resistor with an 820kΩ resistor. This is shown in Figure 10. The second, third and fourth LEDs were disabled by disconnecting...

Words: 1894 - Pages: 8

Premium Essay

Nt1310 Unit 5 Lab Report

...III. EXPERIMENTAL SETTINGS The data are collected from the real time traffic. Collected data are analysed for three metrics: packet delivery ratio, throughput and delay. The packet size is of 64 bytes. All experiments have been performed in outdoor, in indoor environment, at the second floor and at the stairs of our department building. All laptops are in radio range of each other and node 2, 3,4 and 5 are communicating individually to node 1. The time for one experiment was about 60 seconds. Total of 10 trials have been taken and averaged to evaluate the parameters. In moving scenarios, nodes are stopped at corners for about three seconds before moving again. Experimental parameters: Function Value No of nodes 5 Flow Type CBR Packet Size 64 bytes No of Trials 10 Duration 60 sec Parameters Evaluated:...

Words: 632 - Pages: 3

Premium Essay

Nt1310 Unit 5 Lab Report

...detection vector of the k-th user within the target cell is hˆ1k.The average user rate is outlined by PROPERTIES OF BAYESIAN ESTIMATOR Before running simulations, we provide some discussions to understand the properties of Algorithm 1 (namely the Bayesian estimator). Specifically, our aim is to show how the MSE of the Bayesian estimator can be improved over the LS estimator. We begin by investigating the simplest case of not having pilot contamination, i.e., B = 1, and adopt the orthogonal pilot sequences. In that case, combining (2) with (8), we have the following equivalent channel In the higher than analysis, we have a tendency to didn't take into account the pilot interference from different users as a result of the pilot sequences area unit orthogonal. However, within the underdetermined system of interest, the pilot matrix isn't any longer orthogonal. Recent ends up in[23], [24] in contestable that once S is random and sufficiently large, near-minimum MSE (MMSE) estimation continues to be potential via the AMP algorithmic rule. For this reason, the pilot sequences are haphazardly generated for the Bayesian expert. it absolutely was illustrated in [39] that within the large-system limit,11 the output of AMPis comparable to the scalar channel (29) however with a rise inthe background level. Therefore, the MSE of the AMP algorithmic rule is identical to (32) however substitution Δn with an efficient background level Δeff. Recall that AMP is repetitious. Following [39], the effective...

Words: 808 - Pages: 4