Course Project Author Note This assignment is being submitted on September 5, 2013, for N235/CET2629 Section 02 Cisco Networking Fundamentals and Routing course. Course Project Assuming that the router (R1) connecting the NOC to the outside world is configured with an IP address of 154.78.0.1 is directly linked to router (R2) with IP address 154.78.0.244 complete the following: Explain the steps required to configure router R1 and R2 to use Frame relay your explanation should include
Words: 935 - Pages: 4
WAN Design with Frame Relay David Horton CST-443 Abstract This paper gives a high-level overview of how to design a Wide Area Network (WAN) using Frame Relay technology. Aspects of the WAN design process are explored through the use of a fictitious manufacturing company called Zippy's Chips. The Zippy's WAN design covers the topics of weighing alternative technologies, setting up basic Frame Relay Permanent Virtual Circuit (PVC) connections, adding redundant links and scaling the network for future
Words: 3194 - Pages: 13
Week 1 Assignment Your Name Here MIS 589 Networking Concepts and Apps Keller Graduate School of Management Chapter 1 problem 3a and 3b Answer: (a) I think a circuit switched network would be better than a packet switched network in this case. Because when the application starts it will run for a long period of time this works well with a circuit switched network, also the cost of setting it up would be low. (b) Based on having enough bandwidth there is no need for congestion control.
Words: 322 - Pages: 2
TMC1254 Communication and Computer Network Semester 2 2013/2014 Switching 1 Learning Unit Objectives • Understand the concept of switching. • Understand and able to differentiate between different types of switching. 2 • How many connection per device? 3 Introduction • A network is a set of connected devices • How to connect them for communication? – Using mesh topology but wasteful – Used switching • Switched network consists of a series of interlinked nodes, called
Words: 1432 - Pages: 6
likely to be true about this call? Answer: A. It uses a single wire on the local loop at each end of the call. Cabling from the CO to most home telephones uses a single twisted pair of wires, an analog circuit, with the Telco performing circuit switching to switch the analog circuit through the Telco. 2. Which of the following are services that Telco’s have offered as WAN services over the years? (Choose two answers.) Answer: A, Switched analog circuits. B, Dedicated Digital circuits 3. This
Words: 2864 - Pages: 12
apartment. 3. Beach public workout place. 4. Stadium (a place which can play basketball, football and so on.) | - No close substitutes for the main products/services of the industry so that customers are comparatively insensitive to price- Switching costs for customers are quite high | - Close substitutes exist: customers will switch to substitutes in response to price increases. Examples:- less expensive products that serve a similar purpose (e.g. plastic containers instead of aluminum) are
Words: 2036 - Pages: 9
availability, cost, and ease of management. Circuit-switched connections Circuit-switched connections are currently the most popular type of WAN connection. Circuit switching transmits data streams and datagrams across dedicated physical circuits. To provide asynchronous dial-in and ISDN services, the telephone companies use circuit switching. Asynchronous dial-in The public switched telephone network (PSTN) uses circuit-switched technology to provide asynchronous services (otherwise known as normal
Words: 817 - Pages: 4
Matching a) When referring to clocking, the CSU/DSU is this piece of equipment Data Circuit Terminating Equipment (DTE) b) The software used by a router Cisco IOS c) Dialup and ISDN are examples of these types of networks Circuit Switching d) Describes the timing between the router and the CSU/DSU Synchronous e) Lost when a device is powered down or rebooted Contents of RAM f) Wires or other media through which data is transmitted from one place to another
Words: 320 - Pages: 2
1:0 Introductions There are many approaches in business today that managers can use to analyze the business environment such as SWOT analysis, PEST analysis, PORTER’S five forces analysis, four corner’s analysis, Value chain analysis, Early Warming Scans and War Gaming. However, many organizations use Michael Porter’s frame work to analyze business micro environment where the organization/company belongs. Business development managers/ Market Survey managers are mainly critical on analysis of
Words: 2617 - Pages: 11
I work in a market/deli store; working in this type of place it’s usually busy around lunch time which is around eleven to twelve noon. Usually at this time employees will have the right to go on bathroom breaks, smoke breaks, we could be on our cell phones, basically do anything we wanted to do if the store wasn’t busy. Some employees would work through the busy rush not taking a break unless really needed, but others took advantage of the situation and went on two or more breaks within that hour
Words: 386 - Pages: 2
