International Journal of Emerging Technology and Advanced Engineering Website: www.ijetae.com (ISSN 2250-2459, ISO 9001:2008 Certified Journal, Volume 5, Issue 7, July 2015) Design, Simulation & Implementation of A Microcontroller Based Seed Dryer Machine for Farm Produce Interfaced with Computer System Ezeofor J.C1, Okeke. R.O2, Ogbuokebe S.K3 1,2 Department of Electronic & Computer Engineering, University of Port Harcourt, Rivers State, Nigeria 3 National Space Research and Development
Words: 6253 - Pages: 26
The 8051 Microcontroller and Embedded Systems Using Assembly and C Second Edition Muhammad Ali Mazidi Janice Gillispie Mazidi Rolin D. McKinlay CONTENTS Introduction to Computing The 8051 Microcontrollers 8051 Assembly Language Programming Branch Instructions I/O Port Programming 8051 Addressing Modes Arithmetic & Logic Instructions And Programs 8051 Programming in C 8051 Hardware Connection and Hex File 8051 Timer/Counter Programming in Assembly and C 8051 Serial Port Programming in Assembly
Words: 26702 - Pages: 107
Dell™ OptiPlex™ FX160/160 Service Manual Working on Your Computer System Setup Selective USB Reinstalling Software Troubleshooting Computer Stand Covers Hard Drive Assembly (Optional) NVRAM Module Wireless Card I/O Board Power Supply Processor Heatsink Assembly Memory Coin-Cell Battery Cable Guide Antenna System Board Assembly Getting Help Finding Information Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION
Words: 18309 - Pages: 74
MICROCONTROLLER A microcontroller is a computer present in a single integrated circuit which is dedicated to perform one task and execute one specific application. It contains memory, programmable input/output peripherals as well a processor. Microcontrollers are mostly designed for embedded applications and are heavily used in automatically controlled electronic devices such as cellphones, cameras, microwave ovens, washing machines, etc. Types of Microcontroller: Microcontrollers are divided
Words: 595 - Pages: 3
Chapter 3: Jump, Loop, and Call Instructions 3:1: Loop and Jump Instructions 1. In the 8051, looping action with the instruction “DJNZ Rx, rel address” is limited to decrement iterations. 2. If a conditional jump is not taken, what is the next instruction to be executed? Unconditional jump 3. In calculating the target address for a jump, a displacement is added to the contents of register program counter. 4. The mnemonic SJMP stands for short jump and it is a 2-byte instruction.
Words: 686 - Pages: 3
------------------------------------------------- Note: It is a practical guide in which it is presumed that the reader has already learned about the hardware architecture, programming model, and assembly language programming of 8051 microcontroller. In case you are totally new to 8051 microcontroller I recommend you to read the “8051 Tutorial” available at: https://sites.google.com/site/enggprojectece/my-reading-list It has also been presumed that the reader has at least the beginner level knowledge of computer
Words: 3118 - Pages: 13
display. 4. A microcontroller (sometimes abbreviated µC, uC or MCU) is a small computer on a single integrated circuit containing a processor core, memory, and programmable input/output peripherals. Program memory in the form of NOR flash or OTP ROM is also often included on chip, as well as a typically small amount of RAM. 5. Advantages of Microcontrollers a) Microcontrollers act as a microcomputer without any digital parts. b) As the higher integration inside microcontroller reduce cost
Words: 746 - Pages: 3
Interrupt is one of the most important and powerful concepts and features in microcontroller/processor applications. Almost all the real world and real time systems built around microcontrollers and microprocessors make use of interrupts. What is an Interrupt The interrupts refer to a notification, communicated to the controller, by a hardware device or software, on receipt of which controller momentarily stops and responds to the interrupt. Whenever an interrupt occurs the controller completes
Words: 795 - Pages: 4
ACKNOWLEDGEMENT [pic] We would like to thank Asst. Prof., Ila Parmar for her guidance, her support and the opportunity to work on this project and H.O.D., Mr. Lokhandvala for his support and the encouragement. We would also like to thank our families for their constant support, encouragement and motivation without which the accomplishment of this project would not be possible. We would also like to thank our friends and all the people who directly or indirectly played a role in this
Words: 658 - Pages: 3
INDUSTRIAL TRAINING FROM TATA CMC, JAMMU ON EMBEDDED SYSTEMS. Submitted in the partial fulfilment of requirement for the award of degree of Bachelor of Engineering In Electronics and Communication Engineering Submitted By Ashish Gupta 258/12 Under the guidance of Ms. Sonika Mahajan IT Guide Department of Electronics &
Words: 998 - Pages: 4
